3B TECH Inc COOL-P800 User Manual
12
RolliBot RolliCool Mini-Split AC User Manual
WINDOW KIT PARTS
SECTIONS
These sections thread into
one another and should be
placed within a window gap.
A may be fl ipped so that the
opening is higher or lower.
one another and should be
placed within a window gap.
A may be fl ipped so that the
opening is higher or lower.
CONNECTOR
This piece is later inserted into
the opening in Section A and
used to hold the Coolant Lines
in place.
the opening in Section A and
used to hold the Coolant Lines
in place.
SCREW FASTENER
These parts are used to secure
the sections together and
can be loosened or tightened
when adjusting the sections
according to window height.
the sections together and
can be loosened or tightened
when adjusting the sections
according to window height.
A
B
C
Screw Head
Washer
Screw Base
B
A
B
INSTALLATION
Step 1.
Separate one Screw Fastener
and thread the Screw Base
into one end of Section B.
and thread the Screw Base
into one end of Section B.
Step 2.
Thread Section A onto the
end of Section B and use the
Screw Head and Washer to
secure the sections together.
end of Section B and use the
Screw Head and Washer to
secure the sections together.
Step 3.
Repeat Step 1 one at the other
end of Section B.
end of Section B.
B
3.2 – Installing the Outdoor Unit
In order to let off exhaust and hot air, the Outdoor Unit should be placed on level, stable ground
outdoors. The Coolant Lines must be used to connect the two units and may be routed through
a window with the help of the Window Kit.
outdoors. The Coolant Lines must be used to connect the two units and may be routed through
a window with the help of the Window Kit.
Please read all installation steps and parts instructions and information before attempting to install.
13
RolliBot RolliCool Mini-Split AC User Manual
Step 9.
Install the assembled kit
into a window gap and push
the window nearly closed
to secure it in place. Use the
fasteners to adjust as needed.
into a window gap and push
the window nearly closed
to secure it in place. Use the
fasteners to adjust as needed.
Step 4.
Thread Section C onto the
other end of Section B and
use the Screw Head and
Washer to secure the sections
together.
other end of Section B and
use the Screw Head and
Washer to secure the sections
together.
Step 5.
Separate one Screw Fastener
and thread the Screw Base
into one end of the second
Section B.
and thread the Screw Base
into one end of the second
Section B.
Step 6.
Thread the second Section B
into the other end of Section
C and use the Screw Head and
Washer to secure the sections
together.
into the other end of Section
C and use the Screw Head and
Washer to secure the sections
together.
Step 7.
Thread the Coolant Lines into
the side of the Connector
then fi t the Connector into
Section A making sure the
notch is in place.
the side of the Connector
then fi t the Connector into
Section A making sure the
notch is in place.
Step 8.
Check that all Sections are
connected like so.
connected like so.
B
A
C
Screw Fasteners
A
B
C
B
B
B
C
Rollibot-MiniSplitAC-UM-0403.indd Spread 12 of 12 - Pages(12, 13)
Rollibot-MiniSplitAC-UM-0403.indd Spread 12 of 12 - Pages(12, 13)
4/10/2017 7:41:36 PM
4/10/2017 7:41:36 PM