Manualsbrain.com
  1. Manuals
  2. Brands
  3. Transition Networks
  4. C4TEF1017-110
  5. Leaflet

Transition Networks C4TEF1017-110 Leaflet

Download
Page of 1
Ordering Info
C4TEF1011-110
1300 nm multimode (ST)
[2 km/1.2 mi.] Link Budget: 11.0 dB
to
(4) RJ-48 
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m/ 10 ft.]
C4TEF1013-110
1300 nm multimode (SC)
[2 km/1.2 mi.] Link Budget: 11.0 dB
to
(4) RJ-48 
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m/ 10 ft.]
C4TEF1014-110
1310 nm single mode (SC)
[20k m/12.4 mi.] Link Budget: 16.0 dB
to
(4) RJ-48 
[1.5 km / 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m / 10 ft.]
C4TEF1015-110
1310 nm single mode (SC)
[40 k m/24.9 mi.] Link Budget: 26.0 dB
to
(4) RJ-48 
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m/ 10 ft.]
C4TEF1016-110
1310 nm single mode (SC)
[60 km/37.3 mi.] Link Budget: 29.0 dB
to
(4) RJ-48 
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m/ 10 ft.]
C4TEF1017-110
1550 nm single mode (SC)
[80 km/49.7 mi.] Link Budget: 29.0 dB
to
(4) RJ-48 
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m/ 10 ft.]
C4TEF1035-110
1550 nm single mode (SC)
[120 k m/74.6 mi.] Link Budget: 36.0 dB
to
(4) RJ-48 
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m/ 10 ft.]
Single Fiber Products 
Recommended use in pairs 
C4TEF1029-110
1310 nm TX/1550 nm RX single fiber SM
(SC)
[20 km/12.4 mi.] LB: 19.0 dB
to
(4) RJ-48 
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m/ 10 ft.]
C4TEF1029-111
1550 nm TX/1310 nm RX single fiber SM
(SC) 
[20 km/12.4 mi.] LB: 19.0 dB
to
(4) RJ-48 
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m/ 10 ft.]
C4TEF1029-112
1310 nm TX/1550 nm RX single fiber SM
(SC)
[40 km/24.9 mi.] LB: 25.0 dB
to
(4) RJ-48 
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m/ 10 ft.]
C4TEF1029-113
1550 nm TX/1310 nm RX single fiber SM
(SC)
[40 km/24.9 mi.] LB: 25.0 dB
to
(4) RJ-48 
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45) 
[100 m]
plus 6-pin DIN 
[3 m/ 10 ft.]
*Note: RS-232 cable included with each card
(6-pin DIN to DB-9)
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2010 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
AUTO NEG
AUTO CROSS LINK PASS THRU
TRANSPARENT
RAAN AREEN
NS
NT
LINK RESTORE
AUTO
PAUSE
REMOTE MGMT
LOOP BACK
UPGRADE
REMOTE FIRMWARE
Specifications
Standards
IEEE Std. 802.3 2003; Telecordia TR-NWT-001089: FCC Part 68, UL1459; ITU-
T, ANSI, AT&T, ETSI; TBR 12; PD 7024: 1994 (NTR 4); AMI/B8ZS/HD83; G.703
Switches
Numerous switch settings for line coding, line buildout, loopback 
(per port), AIS setting, data/mgmt RS-232 
RS-232 port speed and parity Ethernet port settings: Auto-Negotiation, 
Force speed/duplex and enable Transparent Link Pass Through
Jumper
Hardware: mode is determined by DIP switch settings
Software: mode is controlled by the most recently saved, 
on-board microprocessor setting
Dimensions
Width: 1.72" [44 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Power Consumption
6.0 Watts
Environment
See chassis specifications
Shipping Weight
1 lb. [0.45 kg]
Regulatory Compliance
FCC Class A; VCCI Class A; EN 55022 (CISPR 22) Class A; ICES-003
Warranty
Lifetime
Application
C4TEF10xx-11x
point system™ slide-in-module network interface device
Features

Auto-Negotiation for 10/100BASE-TX 

AutoCross™ (auto MDI/MDI-X) 

Transparent Link Pass Through for 
Ethernet

Automatic Link Restoration 

Pause (Flow Control)

Remote Management

Local and Remote Loopback 

Remote Fiber Loss Signaling

AIS/TAOS

LEDs for each data port

DIP switches for line code, line length, 
local loopback or remote loopback  

T1/E1/J1 mode settings

Dry Relay Contacts on each TDM port

Local (AUX) Management Interface   
(RS232 connector)

Switch selection for Data or 
Management mode on RS232 
interface

Access to complete status information 
on local and remote device

Access to local and remote 
configuration

Switch or SNMP selected Baud 
rate operation

Remote Firmware Upgrade 
4x T1/E1/J1 + 10/100 Ethernet 
Copper to Fiber Transport Mux
see also: 
Stand-Alone NID 
4x T1/E1/J1 + 10/100 Ethernet Transport Mux
Management Features
 
Report local device status:
• Fiber Link Status
• Copper Link Status for each T1/E1
• Hardware switch settings: LBO, AIS   
on C/F, HW/SW, speed
• AIS detected Fiber & Copper
• Model Number
• Copper & Fiber Connectors
 
Local command operations include:
• Loopback Fiber & T1/E1 per channel
• AIS TX on fiber on loss of copper 
link &  AIS TX on copper on loss of 
fiber link
• Serial connection speed and parity 
(Software Mode)
• T1/E1 Mirror Port Modes
• Boot-load firmware upgrades
• Ethernet settings: 
• Auto-Negotiation Enable/Disable
• Force speeds and modes on 
10/100TX
 
Remote device status:
• Fiber Link status
• Copper Link status for each T1/E1
• Hardware switch settings: LBO, AIS 
on C/F, HW/SW, speed
• AIS detected Fiber & Copper
• Model Number
• Copper & Fiber Connectors
 
Remote Commands:
• Loopback Fiber & T1/E1 per channel
• Serial connection speed and parity 
(Software Mode)
• AIS TX on fiber on loss of copper 
link & AIS TX on copper on loss of 
fiber link
• T1/E1 Monitor Modes
• Ethernet settings (Software Mode)
• Force speeds and modes on   
10/100TX
• Enable/Disable: Auto-Negotiation; 
Link  Pass Through; Flow Control; 
& AutoCross™ 

Low cost transport capability: (4) T1/E1/J1; (1) Ethernet 
and (1) RS232 data channel line.

Target applications include: FTTx, such as Fiber-to-the- 
Business, Fiber-to-the-Building, Fiber-to-the-MDU,
Fiber-to-the-Home and Cell tower backhaul.

Copper connections compatible with G.703,   
AMI/B8ZS/HDB3, 10/100BASE-TX, and RS232 channel; 
while the optical connection runs at 155Mbps.

TDM traffic is not mapped to Ethernet. A hardware-
based solution guarantees the constant bit rate of TDM 
transport without requiring traffic management. 
Provides physical layer status monitoring and alarm 
classification functions for Telecom operators to 
manage their fiber optic network and reduce 
operation and maintenance costs.
*Note: C4TEF cards cannot be used with the 1-Slot Point System™ Chassis (see page 30). Devices
must be used in pairs. Typical installation will include a chassis card installed in the Point System™ 
locally and a  stand-alone device (S4TEF) installed at the remote location.
SINGLE 
FIBER