Beijing Hope Tech Global Co. Ltd 00001 User Manual
FCC Requirement
FCC ID: 2APO400001
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna. Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with
FCC radiation exposure limits set forth for an uncontrolled environment. The end user must follow
the specific operating instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter.
and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with
FCC radiation exposure limits set forth for an uncontrolled environment. The end user must follow
the specific operating instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter.
The device is designed to meet the requirements for exposure to radio waves established by
the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6
W/kg. averaged over one gram of tissue. The highest SAR value reported under this standard
during product certification when using the Wi-Fi hotspot function is 0.547W/kg.
the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6
W/kg. averaged over one gram of tissue. The highest SAR value reported under this standard
during product certification when using the Wi-Fi hotspot function is 0.547W/kg.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
In order to ensure compliance with FCC's RF exposure guidelines, this device should be
installed and operated with a minimum distance of at least 10mm between the device and
your body. This includes when using the device in hotspot mode. Only use the supplied
external antenna. Use of other accessories may not ensure compliance with FCC/IC RF
exposure guidelines.
installed and operated with a minimum distance of at least 10mm between the device and
your body. This includes when using the device in hotspot mode. Only use the supplied
external antenna. Use of other accessories may not ensure compliance with FCC/IC RF
exposure guidelines.
Hotspot mode:
This device can provide a hotspot for other WiFi devices. The user can browse, play, and
download media files from the hotpot's local website.
This device can provide a hotspot for other WiFi devices. The user can browse, play, and
download media files from the hotpot's local website.
External Antenna:
Frequency Range: 2412MHz-2462MHz
Gain: 2DBI
VSRW: ≤1.9
Output Impendence: 50Ω
Polarization: Vertical
Connector: RP-SMA
Color: Black
Length (mm): 110mm
Frequency Range: 2412MHz-2462MHz
Gain: 2DBI
VSRW: ≤1.9
Output Impendence: 50Ω
Polarization: Vertical
Connector: RP-SMA
Color: Black
Length (mm): 110mm