CEMTREX ADVANCED TECHNOLOGIES SMARTPODS User Manual
Power on/off, MFB button
Microphone
LED Indicator
User Manual
Overview Of Headset
How To Use
How To Charge
Bluetooth Earphone Specification
Bluetooth Version: V5.0
Bluetooth Protocol: HSP, HFP, A2DP, AVRCP
Standby time: 60H
Talking time: 4H
Music play time: 2.5H
Charging time: 1.5H
Charging Voltage: DC 5V
Working Frequency: 2.402G-2.480G
Environment Temperature: -20/+60
Transmission Distance: 10m
Earbud battery capacity: 45mAh/3.7V
Drive Specification
Driver unit: 8mm
Sensitivity: 9
Impendence:
Frequency Range:
Common question and solution
Bluetooth Pairing
Single earbud:
1. Take one earbud from the case, Long press the MFB until Red&Blue
LED flashing when in the shutdown condition, and sound tip “pairing” .
2. Open the bluetooth of mobile phone, search “ Smart Pods” and click
it to connect the mobile phone ( After sucessful connection, earbud is
blue LED flashing slowly and hear voice tip “pairing sucessful
connected”)
Right and Left earbuds’ connection: In normal condition, the factory fault
is the right and left earbud’ sucessful pairing. Right and left earbud
need to be paired unless no connection.
1. Long press MFB for 6 seconds when in the shutdown condition,It is
red&blue LED flashing, and voice tip is “ pairing”. If pairing sucessfully,
two earbuds are blue led flashing slowly, and voice tip is “pairing
sucessfully connected” .After seconds, if one of the earbud becomes
red&blue LED flashing, and the voice tip is “pairing”, please open the
mobile phones or other devices, and search “smart pods” and connect
them. If connected secessfully, earbud is blue LED flashing, and the voice
tip is “pairing sucessfully second device is connected”.
2. After earbud out of power or power off, earbud will connect to the last
mobile phone automatically when we charging it and power on.
3. If connected with mobile phones ago and cancelled all history on
mobile phone, press two earbuds at the same time until blue LED flash
slowly, the main earbud will be red&blue LED flashing, and open the
bluetooth of mobile phone and connect.
Charging
Earbuds Charging:
1. In chariging, the red LED will flash. In full charging, or power
is enough, the red LED will change to be blue LED (About 1.5
hours charging, earbuds could be charged fully, standards as
LED indicators)
2. If the red LED flashs when connection, earbuds battery is low.
If go on working, earbuds will be powered off automatically, so
please charge earbuds timely.(Put earbuds back to the case to
charge)
3. Earbuds have smart magnet charging, earbuds can be charged
automatically when put earbud back to the case.(If red LED
doesn’t flash, please place earbuds again)
4. After full charging, earbuds can provide talking time for about
3-4 hours, standby time for 100-150hours. For real talking time
and standby time, it depends on different connection of mobile
Thank you for choosing Smartpods product. Your choice is
crucial for us,which means Smartpods has added a new user.
Hope that we will bring you a good experience through our
products and services. Also hope you will put forward the good
advice and suggestions by official customer hotline, Weibo and
Wechat in the process of product experience,which can help
Smartpods to constantly improve product and service.
crucial for us,which means Smartpods has added a new user.
Hope that we will bring you a good experience through our
products and services. Also hope you will put forward the good
advice and suggestions by official customer hotline, Weibo and
Wechat in the process of product experience,which can help
Smartpods to constantly improve product and service.
If you encounter any problems in the using product, please
refer to service process. Your support is our strongest
power, also your recognition and evaluation are a great
encouragement to Smartpods. Thank you!
refer to service process. Your support is our strongest
power, also your recognition and evaluation are a great
encouragement to Smartpods. Thank you!
Smartpods
Power on: When taking two earbuds out
of the case, earbuds will be powered on, pairing and connect the device
automatically, long press MFB for 4 seconds to power on earbuds when in
the shutdown condition.
Power off: Put earbuds back to the case, earbuds will be powered off
automatically, or long press MFB for 4 seconds to to power off
earbuds(red LED) when in the boot condition.
LED INDICATOR
Pairing: Two earbuds will be connected, and red&blue LED flashing, right
earbud is blue LED flashing slowly.
Connected: Blue LED flashs slowly.
Incoming call: Blue LED flashs slowly.
Talking: Blue LED flashs slowly.
Music: Blue LED flashs slowly.
Music play/Stop: Short press MFB to suspend / play the music.
Last song: Long press right MFB for 2 seconds
Next song: Long press left MFB for 2 seconds
Voice assistant: Double click right and left MFB
Last number redial: Three clicks right and left MFB
Manual pairing: Long press MFB for 6 seconds when in the shutdown
condition.
Questions
Reasons
Solutions
NO POWER
ON
NO
CHARGING
NO FOUND
OR FAILURE
PAIRING
BAD
TALKING
SOUND
QUALITY
Exhaustion
of battery power
Press time is short
The charging plug is
not plugged in
properly
Earbuds are not
in the pairing condition
Earbuds are in the
search condition
Application Error of
Mobile Bluetooth
Battery capacity is low
Bluetooth signal
has interference
has interference
Charged in the case(and charged
by mobile phones around
5 mintues more)
Long press MFB for 3 seconds
Place the plug well again
until red&blue LED flash
Let earbuds in the search
condition of the mobile phone
Close the bluetooth of the mobile
phone and then open
bluetooth again
Charge earbuds
Do not apply in noisy environments
or where electromagnetic waves
are dense
FCC Warnning
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modi
fications to this device not explicitly approved
by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
The device can be used in portable exposure condition without restriction.
How To Use
True wireless earbuds
Charging station
Charging cable
How To Charge
Smart Pods
True Wireless Earbuds
True Wireless Earbuds