Polygroup Limited CW002 User Manual
1. Before you start to assemble your tree, choose an appropriate location near a wall outlet.
2. Assemble the tree stand and place on a level surface. (See Fig. A)
2. Assemble the tree stand and place on a level surface. (See Fig. A)
Congratulations on purchasing your new tree from
Polytree®!
This tree assmebles with Quick Set®
technology -Set up and light up your tree in less than 10 minutes! Carefully follow the instructions below
on how to quickly and easily set up your new tree.
on how to quickly and easily set up your new tree.
TREE ASSEMBLY INSTRUCTIONS
Top view
Side view
Fig. C
A
SS
EM
B
LY
IN
ST
R
U
C
TI
O
N
S
M
A
D
E I
N
C
H
IN
A
3. Each tree section is numbered with a tag. Please identify all sections before assembling.
4. Assemble the tree from the bottom to the top. Start with the bottom section and remove protective
cap before inserting into the assembled stand. Make sure the pole is firmly inserted and secured into
the stand.
5. Please remove protective cap from middle section(s) and continue inserting into the bottom section
until the tree top is inserted.
6. Allow branches to fall into place or gently pull up and out. When adjusting branches, be sure that all
wires are free of branch hinges.
7. Insert green label extension cord plug into the wall outlet (see Fig. B ), your entire tree should now be
4. Assemble the tree from the bottom to the top. Start with the bottom section and remove protective
cap before inserting into the assembled stand. Make sure the pole is firmly inserted and secured into
the stand.
5. Please remove protective cap from middle section(s) and continue inserting into the bottom section
until the tree top is inserted.
6. Allow branches to fall into place or gently pull up and out. When adjusting branches, be sure that all
wires are free of branch hinges.
7. Insert green label extension cord plug into the wall outlet (see Fig. B ), your entire tree should now be
lit. If some bulbs do not light or flicker, search for any loose plugs and/or broken, loose or missing
bulbs. Connect the plugs or replace the bad bulbs promptly in order to maintain the performance and
life expectancy of your pre-lit tree.
bulbs. Connect the plugs or replace the bad bulbs promptly in order to maintain the performance and
life expectancy of your pre-lit tree.
8. Begin to shape the branches and tips working from the bottom to the top. Start with tips farthest from
the pole and fan out one to the right, one to the left and one at the center of the main stem. (See Fig. C)
the pole and fan out one to the right, one to the left and one at the center of the main stem. (See Fig. C)
9. After shaping the entire tree following the previous step, slightly upsweep all branch tips for a uniform
look. Shift branches to fill any gaps. Your Christmas tree is now complete and ready to be decorated.
look. Shift branches to fill any gaps. Your Christmas tree is now complete and ready to be decorated.
MODEL #: XXXXXX
*Electrical Rating For The Tree
(For Indoor Use Only)
Input:100-240VAC, 50/60Hz, 0.5A Max.
Output: 29V DC 0.5A
Input:100-240VAC, 50/60Hz, 0.5A Max.
Output: 29V DC 0.5A
Fig. B - Tree and Light Assembly
Power Cord
to Wall Outlet
to Wall Outlet
On/Off Switch
Section 1
Section 2
Section 3
50S
100S
100S
50S
100S
100S
100S
Control box
100S
100S
Do Not Tamper
Internal Parts
Remove the
protective cap
Do Not Tamper
Internal Parts
Remove the
protective cap
Fig. A - Tree Stand Assembly
Slide the legs upwards into slots at the base
of the trunk and tap lightly with hammer
until firmly fixed.
of the trunk and tap lightly with hammer
until firmly fixed.
On/Off
Switch