STETSOM ELECTRONICS USA INC. SX1 User Manual
01
02
03
01
02
03
Power
Central: 6 a 16V dc
Control: Battery CR2032 - 3,0V
Max Consumption
Central: 35mA
Control: 10mA
Central: 6 a 16V dc
Control: Battery CR2032 - 3,0V
Max Consumption
Central: 35mA
Control: 10mA
Technical Specifications
Max. Range in open area:
200m
Modulation:
FSK
Central frequency of transmission: 433,92 MHZ
Max. transmit power:
Max. transmit power:
10mW
Dimensions
Central: 57,5 x 33 x 12 mm
Control: 82,7 x 42 x 15,7 mm
Weight
Central: 46g
Control: 37g
Central: 57,5 x 33 x 12 mm
Control: 82,7 x 42 x 15,7 mm
Weight
Central: 46g
Control: 37g
15
14
16
01
02
03
04
05
06
09
11
10
12
13
Front
Rear
08
07
Control TX1
Central RX1
Long Distance
Remote Control
Remote Control
Quick Guide SX1
Rev 01 -
Apr/2013
17
Alcance Control Manual
Presentation:
The Alcance Control was developed to control audio and video equipment over long
distances. Due to his radio frequency technology (RF), you can control your equipment
up to 200m away in open area (visual).
Its transmission is made in FSK, reducing external interference; its code is encrypted
with "Rolling Code” technology that prevents copying and retransmission signal.
up to 200m away in open area (visual).
Its transmission is made in FSK, reducing external interference; its code is encrypted
with "Rolling Code” technology that prevents copying and retransmission signal.
Description:
01 - Indicator LED of
Transmission / Low Battery.
02 - Power key
03 - Forward and Reward Key
04 - Volume (+) and Volume (-) Key
05 - Up / Down Key
06 - Play / Pause Key
07 - Neck Strap
08 - Cord Neck
09 - Protective Holster
01 - Indicator LED of
Transmission / Low Battery.
02 - Power key
03 - Forward and Reward Key
04 - Volume (+) and Volume (-) Key
05 - Up / Down Key
06 - Play / Pause Key
07 - Neck Strap
08 - Cord Neck
09 - Protective Holster
10 - Antenna
11 - Indicator Led
12 - IR Transmitter Cable (3m)
13 - Polarized Power Cable (50cm)
14 - Infra Red Receiver
15 - Sync Key (Sync)
16 - Learning Key (LRN)
17 - Pin Programming
11 - Indicator Led
12 - IR Transmitter Cable (3m)
13 - Polarized Power Cable (50cm)
14 - Infra Red Receiver
15 - Sync Key (Sync)
16 - Learning Key (LRN)
17 - Pin Programming
Resources:
- The central RX1 can receive commands from up to 7 controls TX1, allowing each
team member has a control.
- A TX1 control can control several devices, even different brands.
- Easy Synchronism. Doesn’t need to use the Assistance Service when purchased
new controls.
- Has several handset models in memory plus function "Learning" that enables the
programming of the vast majority of market controls.
- Low battery indicator on the control and central.
- The central RX1 can receive commands from up to 7 controls TX1, allowing each
team member has a control.
- A TX1 control can control several devices, even different brands.
- Easy Synchronism. Doesn’t need to use the Assistance Service when purchased
new controls.
- Has several handset models in memory plus function "Learning" that enables the
programming of the vast majority of market controls.
- Low battery indicator on the control and central.
Installing your Alcance Control:
The Central can be installed hidden or somewhere visible to monitoring your
indicator Led (11). The most important is that your antenna (10) should be not blocked
by the bodywork of the car that acts as a shield to radio frequency transmission. It can
run close to the edge of one of the windows once the car glass does not block the
reception, or stay inside the panel.
by the bodywork of the car that acts as a shield to radio frequency transmission. It can
run close to the edge of one of the windows once the car glass does not block the
reception, or stay inside the panel.
The power cord (13) is polarized. The wire that has a white stripe should be
connected to the positive pole of the battery and the black wire to negative.
The Infra-Red transmitter (12) must to be fixed at some point inside the car pointing to
CD/MP3-Player panel. Assure that nothing exists between the two.
Synchronizing Your Alcance Control:
The synchronizing is necessary in order the TX1 paring the central RX1. The Alcance
Control goes out from the factory synchronized. This operation is required again in case
the owner to acquire new controls TX1 for your team, replacement or loss of sync.
the owner to acquire new controls TX1 for your team, replacement or loss of sync.
The Alcance Control allows up to 7 TX1 controls are synchronized on the same RX1
central. Each control is addressed in the RX1 central by the TX1 control buttons.
CAUTION: Before performing the synchronizing, make sure that there is any other
control TX1 within the same area being operated. It may to cause interference.
control TX1 within the same area being operated. It may to cause interference.
Follow the steps below to synchronize:
1. Press the Sync (15) key on the Central RX1. The indicator LED (11) flashes.
2. Press one of the keys on the TX1, except the Power key (2).
3. The indicator LED (11) stops flashing. The synchronizing is completed.
1. Press the Sync (15) key on the Central RX1. The indicator LED (11) flashes.
2. Press one of the keys on the TX1, except the Power key (2).
3. The indicator LED (11) stops flashing. The synchronizing is completed.
To synchronize more than one control (maximum 7), repeat the steps 1-3 choosing
different keys in step 2. If you press the same key that has already been used for the
earlier synchronizing, this new control will override the earlier, canceling your
synchronizing.
earlier synchronizing, this new control will override the earlier, canceling your
synchronizing.
You can also undo the synchronizing of each control or all at the same time.
Undoing the synchronizing of a single control:
1. Press the Sync (15) key on the Central RX1. The Indicator LED(11) flashes.
2. Press the Power (2) key in the control TX1 that you want to exclude.
3. The Indicator LED(11) stops flashing. The exclusion is completed.
1. Press the Sync (15) key on the Central RX1. The Indicator LED(11) flashes.
2. Press the Power (2) key in the control TX1 that you want to exclude.
3. The Indicator LED(11) stops flashing. The exclusion is completed.
Exemple: Programming for
CD/MP3-Player - PIONEER
CD/MP3-Player - PIONEER
CD/MP3-Player
Keys
DEH-8380SD
02
03
04
05
01
02
Undoing the synchronizing of all controls:
1. Press the Sync (15) key on the Central RX1. The Indicator LED(11) flashes.
2. Press the Learn (16) key on the Central RX1. The Indicator LED(11) will flash faster
and stop.
1. Press the Sync (15) key on the Central RX1. The Indicator LED(11) flashes.
2. Press the Learn (16) key on the Central RX1. The Indicator LED(11) will flash faster
and stop.
- The exclusion is completed.
Setting the Alcance Control for your CD/MP3-Player:
For the correct operation of your Alcance Control, the central RX1 should be
programed for the model of your CD/MP3-Player. This can be done in two ways, Direct
Mode (using CD/MP3-Player models stored in the memory) or Learning Mode.
Mode (using CD/MP3-Player models stored in the memory) or Learning Mode.
Direct Mode:
1. Look for the code of your CD/MP3-Player in the "Memory” Code Table (See our Manual ).
2. Press the Learn (16) key on the Central RX1. The Indicator LED(11) flashes.
3. Press the Sync (15) key on the Central RX1. The Indicator LED(11) will flash faster.
4. Press on the TX1 control the first key of the table, the Indicator LED(11) stops for a
moment and start blinking again.
5. Press the second key of the table. The Indicator LED(11) will stop.
1. Look for the code of your CD/MP3-Player in the "Memory” Code Table (See our Manual ).
2. Press the Learn (16) key on the Central RX1. The Indicator LED(11) flashes.
3. Press the Sync (15) key on the Central RX1. The Indicator LED(11) will flash faster.
4. Press on the TX1 control the first key of the table, the Indicator LED(11) stops for a
moment and start blinking again.
5. Press the second key of the table. The Indicator LED(11) will stop.
- Your central RX1 is programed to the chosen CD/MP3-Player.
If your DVD/CD/MP3-Player is not listed in the memory code table, try the default setting of your
brand DVD/CD/MP3-Player. (See the Memory Code Table).
brand DVD/CD/MP3-Player. (See the Memory Code Table).