AUDIOPIPE HONGKONG LTD 20130813AP User Manual
Daimo Technology Co., Ltd.
FCC Warning:
Any changes or modifications to this device not explicitly approved by manufacturer could
void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Label Instructions:
The modular transmitter must be equipped with either a permanently affixed label or must
be capable of electronically displaying its FCC identification number.
(A) If using a permanently affixed label, the modular transmitter must be labeled with its
own FCC identification number, and, if the FCC identification number is not visible when
the module is installed inside another device, then the outside of the device into which the
module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter Module FCC
ID: “2AATW-20130813AP” or “Contains FCC ID: “ 2AATW-20130813AP” Any similar
wording
that expresses the same meaning may be used. The Grantee may either provide such a
label, an example of which must be included in the application for equipment
authorization, or, must provide adequate instructions along with the module which explain
this requirement. In the latter case, a copy of these instructions must be included in the
application for equipment authorization.
(B) If the modular transmitter uses an electronic display of the FCC identification number,
the information must be readily accessible and visible on the modular transmitter or on the
device in which it is installed. If the module is installed inside another device, then the
outside of the device into which the module is installed must display a label referring to the
enclosed module. This exterior label can use wording such as the following:
“Contains FCC certified transmitter module(s).” Any similar wording that expresses the
same meaning may be used. The user manual must include instructions on how to access
the electronic display. A copy of these instructions must be included in the application for
equipment authorization.
be capable of electronically displaying its FCC identification number.
(A) If using a permanently affixed label, the modular transmitter must be labeled with its
own FCC identification number, and, if the FCC identification number is not visible when
the module is installed inside another device, then the outside of the device into which the
module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter Module FCC
ID: “2AATW-20130813AP” or “Contains FCC ID: “ 2AATW-20130813AP” Any similar
wording
that expresses the same meaning may be used. The Grantee may either provide such a
label, an example of which must be included in the application for equipment
authorization, or, must provide adequate instructions along with the module which explain
this requirement. In the latter case, a copy of these instructions must be included in the
application for equipment authorization.
(B) If the modular transmitter uses an electronic display of the FCC identification number,
the information must be readily accessible and visible on the modular transmitter or on the
device in which it is installed. If the module is installed inside another device, then the
outside of the device into which the module is installed must display a label referring to the
enclosed module. This exterior label can use wording such as the following:
“Contains FCC certified transmitter module(s).” Any similar wording that expresses the
same meaning may be used. The user manual must include instructions on how to access
the electronic display. A copy of these instructions must be included in the application for
equipment authorization.
Note:
The OEM integrator is still responsible for the FCC compliance requirement of the end
product, which integrates this module.
Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment
authorizations (e.g. Verification , Doc) of the host device to be addressed by the
integrator/manufacturer.
product, which integrates this module.
Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment
authorizations (e.g. Verification , Doc) of the host device to be addressed by the
integrator/manufacturer.