ALCOMA a.s. AL24GMPBDP User Manual
Microwave data link ZENITH 24
1/59
1.1
1.
INTRODUCTION
The radio relay link ZENITH 24 as a whole or as parts is not intended to be used by untrained
personnel. Installation, adjustments and maintenance must be performed only by a person with
electrotechnical qualifications trained by the manufacturer.
electrotechnical qualifications trained by the manufacturer.
Warning RF Exposure Compliance
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least
126 cm from all persons and must not be co‐located or operating in conjunction with any other antenna or
transmitter. Users and installers must be provided with antenna installation instructions and transmitter
operating conditions for satisfying RF exposure compliance.
FCC/Industry Canada Two Part Stmt:
transmitter. Users and installers must be provided with antenna installation instructions and transmitter
operating conditions for satisfying RF exposure compliance.
FCC/Industry Canada Two Part Stmt:
This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme à FCC Partie15 d’Industrie Canada RSS standard exempts de licence (s). Son
utilisation est soumise à Les deux conditions suivantes: (1) cet appareil ne peut pas provoquer
d’interférences et (2) cet appareil doit accepter Toute interférence, y compris les interférences qui peuvent
causer un mauvais fonctionnement du dispositif.
d’interférences et (2) cet appareil doit accepter Toute interférence, y compris les interférences qui peuvent
causer un mauvais fonctionnement du dispositif.
This device complies with Health Canada’s Safety Code. The installer of this device should ensure that
RF radiation is not emitted in excess of the Health Canada’s requirement. Information can be obtained at
http://www.hc‐sc.gc.ca/ewh‐sem/pubs/radiation/radio_guide‐lignes_direct‐eng.php
http://www.hc‐sc.gc.ca/ewh‐sem/pubs/radiation/radio_guide‐lignes_direct‐eng.php
Cet appareil est conforme avec Santé Canada Code de sécurité 6. Le programme d’installation de cet
appareil doit s’assurer que les rayonnements RF n’est pas émis au‐delà de I’exigence de Santé Canada. Les
informations peuvent être obtenues: http://www.hc‐sc.gc.ca/ewhsemt/pubs/radiation/radio_ guide‐
lignes_direct‐eng.php
informations peuvent être obtenues: http://www.hc‐sc.gc.ca/ewhsemt/pubs/radiation/radio_ guide‐
lignes_direct‐eng.php
“Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.”
"Les changements ou modifications non expressément approuvés par la partie responsable de la
conformité pourraient annuler l'autorité de l'utilisateur à utiliser cet équipement."
The link ZENITH 24 is an information technology device, to which the ČSN EN 50 116 – Routine
electrical safety testing in production standard applies. If the power supply (BKE‐JS 38 – 480/UK,
BKE‐JS 150 – 480/DIN) is a part of delivered merchandise, a copy of its testing protocol can be ordered from
the manufacturer.
BKE‐JS 150 – 480/DIN) is a part of delivered merchandise, a copy of its testing protocol can be ordered from
the manufacturer.
Please read this operation manual carefully before installation and operation of the duplex microwave
link for data transmission ALCOMA ZENITH 24. Please pay increased attention to the safety instructions that
are marked like this in the text:
are marked like this in the text:
WARNING
Violating of this marked safety instructions can cause serious injury to personnel.
Violating of this marked safety instructions can cause serious injury to personnel.
CAUTION
Violating of this marked instructions can cause damage to the equipment.
Violating of this marked instructions can cause damage to the equipment.