Atoms Labs LLC AWFB17R User Manual
B. Wi-Fi Network Setup
(B1) Launch SensorCam app and tap
(B2) Scan the barcode label on the back of the camera to bring up the DID
information, or manually type in the DID, including the dashes.
(B2) Scan the barcode label on the back of the camera to bring up the DID
information, or manually type in the DID, including the dashes.
(B3) Name your camera (max. 20 characters).
(B4) Enter default security code: 123456.
(B5) Tap to save information and follow the in-app
wizard to complete the setup process.
QUICK START GUIDE
KIT CONTENT
Wireless SensorCam
x 1
Adapter DC 5V/1.5
x 1
Quick Start Guide
x 1
x 2
Battery (18650 Type)
IMPORTANT
Please Notice Below Before You Setup The SensorCam:
- SensorCam offers public cloud storage function, to use this function please have Google Drive or
Dropbox account information ready.
- After initial setup, please charge the camera for 4 to 6 hours before going completely wireless. Once
the camera is fully charged, user will receive push notification.
- You can search the “OMGuard HD” APP on the APP Store or Google Play Store. Or scan the QR code.
Dropbox account information ready.
- After initial setup, please charge the camera for 4 to 6 hours before going completely wireless. Once
the camera is fully charged, user will receive push notification.
- You can search the “OMGuard HD” APP on the APP Store or Google Play Store. Or scan the QR code.
- Make sure your device is connecting to Wi-Fi network.
- For maximum performance, please only use Class 10 rated SD card. Camera will not function
without SD card inserted.
- Please make sure to unbind your cloud storage account before transferring ownership of the camera.
- For maximum performance, please only use Class 10 rated SD card. Camera will not function
without SD card inserted.
- Please make sure to unbind your cloud storage account before transferring ownership of the camera.
SETUP THE SENSORCAM
A. MicroSD Card/Battery Installation
(A1) Remove the battery compartment cover to insert MicroSD card. Follow the steps below to insert
the MicroSD card.
the MicroSD card.
(A2) Insert two 18650 batteries and connect the wires. Then the camera will power up that status
LED will flash red/blue (continue to Section B - Wi-Fi Network Setup). Make sure the battery
cables are firmly connected to the camera, or press and hold the reset button until the status
LED flashes red/blue.
(B1)
(B2)
(B3)
(B4)
(B5)
Battery compartment for 18650 x 2
Memory Card Slot (Push left to unlock the cover, flip up & insert card)
Factory Reset Button (Long press for 6 sec until status LED flashing in blue)
Memory Card Slot (Push left to unlock the cover, flip up & insert card)
Factory Reset Button (Long press for 6 sec until status LED flashing in blue)
Default PW: 123456
Wi-Fi Pairing Mode:
SSID: SensorCam-123456
Default PW: 12345678
Wi-Fi Pairing Mode:
SSID: SensorCam-123456
Default PW: 12345678
Barcode lable: COXX-123456-ABCDE
DID Example:
COXX-123456-ABCDE
COXX-123456-ABCDE
Status LED
Light Sensor
Motion Sensor
Light Sensor
Motion Sensor
White-Light LED
HD Camera
5V Micro USB Power Input
Wake Up Button(Short Press)
Motion Alert On/Off Switch(Long Press)
Stand Mounting(Bottom)
Stand Mounting(Rear)
Battery Compartment
(18650 x 2)
Memory Card Slot
(Support up to 32GB)
To Activate Motion Alert: Long press for 5 sec until Red LED blink once
To Deactivate Motion Alert: Long press for 5 sec until Blue LED blink once
Connect here
Battery Compartment Cover
Note: when you insert
batteries, please notice this
side up.
batteries, please notice this
side up.
For iOS
For Android
UP
UP
UP
UP
Push forward to
unlock the cover
2
Flip up the cover
3
Insert the SDcard
and close the cover
4
Push forward
to lock the cover
5
Remove the battery
compartment cover
1
Push forward
to close the cover
6
Li-On Battery Operated Wireless Network Camera
AWFB17R