Professional Security Corporation DBA Personal Safety Corporation WAM-1 User Manual
TM
PATIENT
MONITORING SYSTEM
• Wireless Alarm Monitor – Model No. WAM-1
• Wireless Alarm Transmitter – Model No. WAT-1
• Wireless Bed Sensor Pad (One Year) – Model No. BEDPAD-1W
• Wireless Chair Sensor Pad (One Year) – CHAIRPAD-1W
• Wireless Floor Mat Sensor (One Year) – MAT-1W
Made in China • One Year Warranty • Patent Pending
Quick Setup
1. Insert 3 AA batteries into Alarm Monitor (WAM-1) & 2 AAA
batteries into Transmitter (WAT-1).
2. Press & hold Alarm Monitor SYNC button. Red light
turns on.
3. Press Transmitter SYNC button. Red light turns on and
Alarm Monitor beeps once.
4. Both red lights will turn off. Monitor & Transmitter are now
synced. Test before each use.
WARNING: Changes or modifications to this product that
are not authorized by the manufacturer may void FCC
compliance and negate the user’s authority to operate this
product.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses
and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment
and receiver.
3. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
System Overview
The Secure
®
Wire-Less Patient Monitoring System takes fall
management patient alarms to the next level by eliminating
tripping hazards, taking the alarm sound out of the patient
room, and employing the most advanced, patent pending
continuous 2.4G bi-directional wireless communication that
ensures secure communication between the Wireless Alarm
Monitor (WAM-1) and Wireless Alarm Transmitter (WAT-1)
housed in the pocket of a Secure
®
bed or chair sensor pad or
floor mat sensor.
When a patient gets off the monitoring pad housing the
When a patient gets off the monitoring pad housing the
transmitter, the transmitter will instantly send a wireless
signal to the monitor without a dangerous delay that is
found in other patient monitors. The monitor will then send a
confirmation signal to the transmitter to stop the transmitter
signal conserving battery life.
The monitor will automatically reset once the patient gets
The monitor will automatically reset once the patient gets
back on the bed/chair sensor pad. Alternatively, the monitor
can be reset by pressing the reset button located on the front
of the monitor. When using a floor mat sensor, the monitor will
continue to alarm until the reset button is pressed.
The monitor may be connected to a standard nurse call
The monitor may be connected to a standard nurse call
system using the optional Nurse Call Cable accessory (NCI-
1). When connected to a nurse call system, the monitor alarm
sound may be left on or muted to eliminate in-room alarm
noise. The Monitor will activate the nurse call system to alert
the nurses’ station of unsafe patient egress.
When in standby, the monitor and transmitter communicate
When in standby, the monitor and transmitter communicate
every 5 minutes to confirm both remain synced. If the monitor
and transmitter become unpaired the 3rd LED light on the
front of monitor will flash continuously and the alarm will
sound continuously indicating the system is not functioning
properly.
Setup Instructions
(Call 800-3-Secure for Setup Help)
1. Wireless Alarm Monitor (WAM-1) –
1. Wireless Alarm Monitor (WAM-1) –
Install Batteries& Set Volume/Tone
• Remove WAM-1 from protective holder
• Fully loosen battery cover screw with included
screwdriver
• Open battery cover by sliding in a downward motion
• Insert 3 AA batteries (included) into the battery
compartment ensuring correct polarity
Personal Safety Corporation • Hiawatha, Iowa 52233 • 800.373.2873