Extron Electronics EXTWAP100AC User Manual
12 VDC power
input
input
page 7
B
12 VDC power input
(see page 4)
— power supplies must be purchased separately.
Extron recommends using a PoE power injector. If you wish to use a power supply,
connect a 12 VDC, minimum 1.0 A power supply with a DC plug to the power input.
See
connect a 12 VDC, minimum 1.0 A power supply with a DC plug to the power input.
See
for
suitable models.
NOTES:
•
The WAP 100AC ships without a power supply. Either a 12 VDC, minimum
1.0 A power supply or a PoE+ (802.3at compliant) power injector must be
purchased separately.
1.0 A power supply or a PoE+ (802.3at compliant) power injector must be
purchased separately.
•
Do not use both the 12 VDC power supply and power injector at the same time.
ATTENTION:
•
Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and
may cause damage to the supply and the end product.
unauthorized power supply voids all regulatory compliance certification and
may cause damage to the supply and the end product.
•
Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit final.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit final.
•
These products are intended for use with a UL Listed power source marked
“Class 2” or “LPS” and rated 12 VDC, minimum 1.0 A. or PoE+ (802.3at
compliant) power injector.
“Class 2” or “LPS” and rated 12 VDC, minimum 1.0 A. or PoE+ (802.3at
compliant) power injector.
•
Ces produits sont destiné à une utilisation avec une source d’alimentation listée UL
avec l’appellation « Classe 2 » ou « LPS » et normée 12 Vcc, 1,0 A minimum ou
avec l’appellation « Classe 2 » ou « LPS » et normée 12 Vcc, 1,0 A minimum ou
French Translation
.
•
Extron power supplies are certified to UL/CSA 60950-1 and are classified as
LPS (Limited Power Source). Use of a non-LPS or unlisted power supply will
void all regulatory compliance certification.
LPS (Limited Power Source). Use of a non-LPS or unlisted power supply will
void all regulatory compliance certification.
•
Les sources d’alimentation Extron sont qualifiées UL/CSA 60950-1 et sont classées
LPS (Limited Power Source). L’utilisation d’une source d’alimentation non-listée ou
non-listée LPS annulera toute certification de conformité réglementaire.
LPS (Limited Power Source). L’utilisation d’une source d’alimentation non-listée ou
non-listée LPS annulera toute certification de conformité réglementaire.
•
Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within the same vicinity
as the Extron AV processing equipment in an ordinary location, Pollution Degree 2,
secured to the equipment rack within the dedicated closet, podium, or desk.
spaces or in wall cavities. The power supply is to be located within the same vicinity
as the Extron AV processing equipment in an ordinary location, Pollution Degree 2,
secured to the equipment rack within the dedicated closet, podium, or desk.
•
Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales. La source
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel
dans un endroit ordinaire, avec un degré 2 de ption Ext4 fixé à un équipement de
rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
utilisation dans les espaces d’aération ou dans les cavités murales. La source
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel
dans un endroit ordinaire, avec un degré 2 de ption Ext4 fixé à un équipement de
rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
•
The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16.
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16.
•
Cette installation doit toujours être en accord avec les mesures qui s’applique au
National Electrical Code ANSI/NFPA 70, article 725, et au Canadian Electrical
Code, partie 1, section 16.
National Electrical Code ANSI/NFPA 70, article 725, et au Canadian Electrical
Code, partie 1, section 16.
•
The power supply shall not be permanently fixed to the building structure or
similar structure.
similar structure.
•
La source d’alimentation ne devra pas être fixée de façon permanente à une
structure de bâtiment ou à une structure similaire.
structure de bâtiment ou à une structure similaire.
WAP 100AC • Panel Features
7