WOW CREATIONS HK LTD. ON BEHALF OF GIGGLES INT'L LTD. GI-BT2300 User Manual

 

 

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the 

following two conditions : (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation. Caution : changes or modifications not expressly approved

by the party responsible for compliance could void the user’s authority to operate the 

equipment. NOTE : This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a 

residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures :

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver. 

- Connect the equipment into an outlet on a circuit different from that to which the receiver 

  is connected.

- Consult the dealer or experienced radio/TV technician for help. 

Modifications not authorized by the manufacturer may void the user’s authority to operate

this device.

Speaker

Total Output

Battery / Voltage 

Playback Time

Compatibility

Operating Range

1. Turn on the Bluetooth  on your device.

    (Refer to your device’s user manual for details if necessary.)

2. Make sure your device is within the operating range (25-30 feet) of the speaker.

3. Slide 3-way switch to “ON” position. The light-up face will flash and the speaker will make a beeping

    sound which indicates the product is in AUTO-PAIRING mode.

4. The product will go into SLEEPING mode automatically if it does not pair with any device after  

    10 minutes. To reactivate the AUTO-PAIRING mode, simply turn 3-way switch OFF and turn it back ON.

5. Once the product is in AUTO-PAIRING mode, look for “Pumpkin SPK” on your device and connect. 

    Once the product is connected with your device, it will make another beeping sound. 

(after the product is successfully paired with your device):

1. Activate your audio device as you normally do.

2. Turn 3-way switch to “OFF (TRY ME)” position to preserve battery life if not in use.

If you have any questions about this product, pls contact us at 

info@wowcreations.net

The product complies with the FCC portable RF exposure limit set forth for an uncontrolled

environment and are safe for intended operation as described in this manual. The further 

RF exposure reduction can be achieved if the product can be kept as far as possible from 

the user body or set the device to lower output power if such function is available.

1. Locate battery compartment on the bottom of the product.

2. Turn the 3-way switch to “OFF (TRY ME)” position.

3. Open battery compartment cover by removing screw with a Phillips

    head screwdriver.

4. Insert / replace 3 “AA” batteries - follow polarity diagrams inside the

    battery compartment.

5. Replace the cover and turn 3-way switch back to “ON” to activate the

    Bluetooth  function or turn switch to “LIGHTS ONLY” position to use

    the product as a light-up decoration.

- Do not mix old and new batteries.

- Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel cadmium) batteries.

- Non-rechargeable batteries are not to be recharged.
- Batteries should only be changed under adult supervision.
- Do not dispose of batteries in fire, batteries may explode or leak.
- Exhausted batteries are to be removed from the product.
- The supply terminals are not to be short-circuited.
- Do not use rechargeable batteries.
- Batteries are harmful if swallowed, so keep away from young children.
- Only batteries of the same or equivalent type as recommended are to be used.
- Clean the battery contacts and also those of the device prior to battery installation.
- Remove battery if product left unused for a long time. 

1. Locate 3-way switch (FIG. B) on the bottom of the product.

2. Default setting of 3-way switch is set to “OFF (TRY ME)” for store 

    demonstration. Bluetooth  function is disabled in this setting.

3. To turn on the Bluetooth  function, slide 3-way switch to “ON” position

    to pair your device with this product.

    (See pairing instruction below under “PAIRING YOUR DEVICE”.)

4. To operate this product as a light-up decoration, turn 3-way switch to “LIGHTS ONLY” position. 

    Product is equipped with a two hour automatic timer (2 hours on / 22 hours off).

    * Lights will operate for 2 hours and will automatically turn off for 22 hours.  If “LIGHTS ONLY” 

      switch is left on, the lights will turn on for two hours 24 hours after initial activation of “LIGHTS

      ONLY” setting.  

Bluetooth  and the Bluetooth  logo are registered trademarks of Bluetooth SIG, Inc. and any use 

of such marks by WOW! Creations is under license.

    2014 WOW! Creations HK Ltd. All Rights Reserved. Patent Pending. 

This products requires 3 “AA” size Alkaline Batteries (INCLUDED). Batteries included are for store 

demonstration so replacement batteries should be purchased for best performance.

Can’t Pair With 

Device

Make sure the pumpkin speaker is on and the device has its Bluetooth  turned on.

Check if the pumpkin speaker is turned on; check batteries and replace with fresh 

batteries if batteries are low.

Make sure the device is within 3 feet from the product to detect the Bluetooth  stream.
Check if the pumpkin speaker is paired with another device. Unpair it from any 

current existing device if necessary to make the pumpkin speaker available for 

your desired device.

No Sound

Check if the pumpkin speaker is successfully paired with the device or not.
Check the sound volume on your device and try to turn up the volume.

Sound Distortion

Check and make sure your pumpkin speaker is within 33 feet from your device.

Try to turn off the WIFI on your device

C

: 1.5” (40mm)

: 3 watt full-range amplifier

: Three AA size Alkaline Batteries / 4.5V

: Approx. 7 hours at 70% volume

: Bluetooth  2.0 or above

: Up to 33 feet (10 meters)

The ‘TRY ME’ wire is connected to the bottom of the product during in packaging demonstration only.

‘TRY ME’ wire can be removed during normal operation.