SUNstone Digital Limited JTL-10 User Manual
Charging
To charge the speaker, connect the USB cable directly to a PC or laptop or to a mains USB
charger.The LED indicator on the speaker will turn red when charging.The LED indicator will
turn off once the battery is fully charged.
The speakers can be used while being charged( speaker is on, connect with 3.5mm line-in
cable),the LED indicator will flicker blue and red.
Full charging time for a flat battery is 3~4 hours.
BLUETOOTH connecting
Make sure the 3.5mm line-in cable is not connected.
Connect the speaker ,Turn the Main speaker ON. You will hear a special tone to indicate
Bluetooth functionality,the LED indicator will flicker blue.
On your phone or laptop search for a new Bluetooth device called “ BT Speaker”.
If you are asked for a password enter ‘0000’.
WIRED connecting
Connect the line-in cable to your audio source on one end and to the speaker using the USB
port on the other end. Turn the main speaker ON.Start playing music.
When the line-in cable is connected,the Bluetooth module is disabled and audio is then routed
to the speaker through wires .
● Bluetooth Protocol : 4.0 +EDR(support A2DP)
● Transmission Distance : Up to 10 meters(open space)
● Line Input : Φ3.5mm
● Battery Voltage : 3.7V
● Charging Voltage 5V
● Power Input Mini USB (5V/500mA)
To charge the speaker, connect the USB cable directly to a PC or laptop or to a mains USB
charger.The LED indicator on the speaker will turn red when charging.The LED indicator will
turn off once the battery is fully charged.
The speakers can be used while being charged( speaker is on, connect with 3.5mm line-in
cable),the LED indicator will flicker blue and red.
Full charging time for a flat battery is 3~4 hours.
BLUETOOTH connecting
Make sure the 3.5mm line-in cable is not connected.
Connect the speaker ,Turn the Main speaker ON. You will hear a special tone to indicate
Bluetooth functionality,the LED indicator will flicker blue.
On your phone or laptop search for a new Bluetooth device called “ BT Speaker”.
If you are asked for a password enter ‘0000’.
WIRED connecting
Connect the line-in cable to your audio source on one end and to the speaker using the USB
port on the other end. Turn the main speaker ON.Start playing music.
When the line-in cable is connected,the Bluetooth module is disabled and audio is then routed
to the speaker through wires .
● Bluetooth Protocol : 4.0 +EDR(support A2DP)
● Transmission Distance : Up to 10 meters(open space)
● Line Input : Φ3.5mm
● Battery Voltage : 3.7V
● Charging Voltage 5V
● Power Input Mini USB (5V/500mA)
Federal Communications Commission (FCC) Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: