BAYANG MODEL AIRPLANE TOYS FACTORY BY201724GR User Manual

least 20cm from nearby persons.

ance with the FCC’s RF exposure guidelines, place the drone

SMALL PARTS NOT FOR CHILDREN UNDER 3 YEARS.
ADULT ASSEMBLY REQUIRED.

Remote Controller Battery: 3 x 1.5V AAA
Charging Time: Approximately 180 minutes

Drone Battery: 850 mAh Li-Po

Maximum Recommended Altitude 120 ft.

General Warnings 

Page 1

Contents and Remote Battery Installation 

Page 2

Charging Battery and Replacing Propellers

Page 3

Remote Overview 

Page 4

Operating Drone 

Page 5

Modes

Page 6

Tips and FCC Warning

Page 7

1. Unscrew and open the battery compartment.

2. Install 3 “AAA” batteries as shown in the diagram 

    shown above.

3. Replace and close battery compartment.

Turn off the drone before charging. 

Connect the Battery Charge Cable to the charging

port on the Drone.
Connect USB connector to power source.

Congratulations on your purchase of 

the Streaming 2.4 GHz Coventry 

Aviation Drone. Get ready to soar to 

new heights. Master the art of drone 

flying and stunts with remote control 

maneuverability. This lightweight stunt 

drone will provide hours of fun. 

Note: The Battery Charge Cable will light up 

when it is charging the battery and turn off 

when the battery is fully charged. Charge time 

is approximately 180 minutes.

Stunt button

Auto Orientation

Spin Trim

Controls

flight direction

Throttle Joystick

 

 

Increases or decreases 

 

drone elevation

  

 

Spins Drone

The drones range is approximately 250 feet or 120 feet of altitude:

 

• Read and be aware of all warnings found on Page 1.

 

• Maintain your desired elevation by using the Throttle.

 

• Push the Throttle joystick to right or left to spin the drone.

 

• Use the right joystick to move forward backwards, and side  

 

   to side.

 

• Review step 5 if your drone begins to drift.

 

• Drone will begin to blink when drone is paired to remote 

  

   and battery is low. 

Follow this step if your drone begins to drift while take off or     

during flight.

 

• Drone drifts backwards: Press the forward Direction      

Trim Button.

 

• Drone drifts forwards: Press the Backwards Direction    

Trim Button.

 

• Drone drifts left: Press the Right Direction Trim Button.

 

• Drone drifts right: Press the Left Direction Trim Button.

 

• Drone spins clockwise (viewing drone from top): Press the 

Left Spin Trim Button

 

• Drone spins counter-clockwise (viewing drone from top): 

Press the Right Spin Trim Button

There are two ways to land the drone:

1. Press the Auto Land Button. The drone will slowly begin to land. If 

     the drone begins to drift, you can still control the drone’s 

     direction using the Multi Directional Button.

2. Slowly and carefully press the Throttle Joystick down until drone 

     lands. If the drone begins to drift, you can still control the drone’s 

     direction using the Multi Directional Button.

• Drone is designed to be flown indoors and 

outdoors.

• Always make sure you have enough space to fly 

drone.

• Always follow warnings, page 1.
Step 3 – Starting Drone

1. Making sure your remote is off, slide drone switch 

to ON. Drone lights will begin to flicker.

2. Place drone on a flat even surface with clearance 

according to diagram (Fig 1). 

3. Turn remote on. Make sure the left stick (throttle) 

is in a neutral position (stick is centered). 

4. Push the stick up and then down.

5. A single tone indicates that the drone is paired. 

Drone lights will  flicker rapidly then turn on 

permanently once paired. 

6. If pairing is unsuccessful, repeat steps 3-4.

Slowly and carefully press the Throttle Joystick up. 

Drone will begin to elevate. You can compensate for 

some of the drones drifting by using the Multi 

Directional Button or by following Step 5. You may 

need to practice this step several times before 

successfully getting drone into the air.

Once you are comfortable flying the drone, use the Stunt Button to perform acrobatic stunts.

 

1. Hover the drone to at least above 10 feet.

 

2. Press the Stunt Button. You will hear beeping coming from the remote.

 

3. Move the Multi Directional Button to the desired direction that you would like the drone to flip.

•  Auto Orientation default setting is off. To enter this mode press Auto Orientation button.  Remote will beep twice. 

•  After drone is successfully paired, the 2 white LED lights toward orientation will be the original forward orientation, when drone 

is in auto orientation mode, the drone will orient to the user (remote), no matter what direction the drone is facing. Pushing the 

right stick up will send the drone away from the user, pushing it to the right will move the drone right, etc. 

•  Remote will beep every 6 seconds to indicate the drone is in Auto Orientation mode.

•  To exit mode, press the Auto Orientation button. Remote will sound 1 long beep indicating that it has exited Auto

   Orientation mode. 

Note: Auto Orientation mode is oriented to the user when pairing. If the remote is moved after pairing Auto Orientation, please 

follow directions above to reset Auto Orientation.

•  Make sure you have achieved level, balanced flight, where the drone is neither climbing nor descending. This mode allows you 

   to safely and slowly land your drone without having to control the speed.  It is done for you automatically.

•  The ideal auto landing height is 25-30 ft.

•  Press the Land button to trigger auto land. Remote will beep continuously until you exit the auto land mode. 

•  To steer the drone during landing, use the right control until drone has reached the ground.

•  Press the Land button again to exit auto landing mode.

•  Taking a picture- press camera icon on app once to take a picture.

•  Creating video- press video icon on app once to take a video. Press the video icon on app again to stop recording.

Connect the Charging

Cable to the Drone

Insert the 

Charging Cable

into a USB

power source

1. Read all warnings and instructions.

2. Install remote batteries, page 2.

3. Make sure that drone and remote are powered off.

4. Install drone holder.

5. Charge batteries, page 3.

• 

Not recommended for children under 12 years of age. As with all electrical products, precaution

 

should be observed during handling and use to reduce the risk of electrical shock.

• 

Adult supervision is required at all times.

• 

Before each use, an adult should review the product and battery to determine that no damage          

 or 

hazards exist.

• 

Do not allow anything to intentionally make contact in any way with spinning propellers.

 

 

• Prevent contact with spinning blades by turning off remote prior to handling drone.

• 

Keep drone away from power lines, buildings, trees, public areas, and any other potentially 

 

hazardous areas.

• 

Do not operate in rain, heavy wind, and or any type of severe weather.

• 

Do not land drone on wet surfaces.

• 

Never touch or allow others to touch drone while it is flying.

• 

Always turn drone off when it is not in use.

• 

Always fly drone in large open areas.

•        Never fly drones above or near people, sudden changes in wind or other conditions could lead to 

         unexpected crashes.

•        Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and 

         property rights of others.

•        The drone shall never be modified or used for anything except its intended purpose.

•          Only charge the rechargeable drone battery using the included charging cable.

•  Do not crash drone into sand or dirt. Drone gears may become clogged.

•  When first learning to fly, practice lifting off and hovering.

•  Stay several feet from walls and buildings.

•  Always press throttle all the way down after crashing or when something gets stuck in propellers.

•  Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes.

•  Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others.

•  The drone shall never be modified or used for anything except its intended purpose.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s 

authority to operate the equipment.

When remote switch is turned on, the remote light does not illuminate:

 

1)      Check that batteries in the remote are installed correctly OR

 

2)      Replace with new batteries.

During drone flight, the remote LED is flashing:

 

1)      Remote batteries are low; replace them with new batteries.

Drone and remote properly pair, but the drone will not lift-off:

 

1)      Drone battery needs charging. Use the USB Charge Cable to connect the drone to 

 

         power source.

After trimming the drone, the drone flight is very unstable and cannot fly properly:

 

1)      One or more blades are most likely damaged;

 

2)      Turn off the drone and remote.

 

3)      Replace with the proper number replacement blade and try flying again.

After impact, the drone is unstable:

 

1)      Put the left remote control lever to the left bottom and put the right  remote control lever

 

         to the right bottom at the same time. This will reset the gyroscope (Fig. 1).

 

2)      If the above does not resolve the issue, reboot the drone and controller and pair again. 

Remote Controller and Drone can not be paired:

 

1)      Check Point: Remote Controller must be closed to Drone, not exceed 12 feet.

Note: If there are 2 sets of Drones within 12 feet for Pairing, you must pair one successfully before pairing the second set. 

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications. However there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one 

or more of the following measures:

 

- Reorient or relocate the receiving antenna,

 

- Increase the separation between the equipment and receiver.

 

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 

- Consult the dealer or an experienced radio/TV technician for help. 

FCC RF Radiation Exposure Statement Caution: To maintain compli

FAO

®

 and FAO Schwarz

®

 names and logos are trademarks or registered trademarks. All rights reserved. Distributed by ©2017 MerchSource, LLC, Irvine, CA 92618. For customer 

support please call 888-987-6533.

The artwork and design of this package are protected by US copyright law and may not be reproduced, distributed, displaced, published or used for any purpose without prior written 

permission. Altering, removing or reproducing any of the trademark or copyright notices on this package is not permitted.

PATENT PENDING

Printed in China      

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause 

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Always be mindful of others privacy and do not 

record video or take images of others without 

their consent. Check and comply with your 

federal, state and local laws regarding privacy. 

1. Follow diagram

2. Remove screw from top of Propeller

3. Remove broken Propeller and replace 

    with new Propeller

4. Make sure you installed the correct 

    blade. Each blade has a number 

    written on it. Match the blades with 

    the corresponding number on the 

    drone

5. Insert screw into top of Propeller

1. Press the connect to Wi-Fi 

    button

2. Follow the on screen 

    instructions

1. Press the Stream Button to 

    begin streaming

2. Press the Album Button to 

    review pictures and videos

Go to your app store on your smart phone and download the “FAO Drone” application. 

Directional 

Trim

Speed

Control

Auto Landing

Before each flight pair the remote with the drone:

 

1. Turn your drone on and place on a flat, level surface

 

2. Turn on the remote on and move the left joystick up, then down

 

3. The beep will indicate successful pairing

 

4. Repeat steps 1 and 2 if necessary

•    White lights indicate the front of the drone

•    Red lights indicate the back of the drone

•    Not applicable in auto-orientation mode

Practice flying your drone below 10 feet and at low speeds until comfortable with all                  

controls to avoid unnecessary damage or injury

 

•    Left joystick:

 

 

• Up/Down controls elevation

 

 

• Left/Right controls spin

 

•    Right joystick: controls flight direction

 

•    Direction Trim: use to eliminate drift

To cut power to drone, move left joystick to down position 

•    Drone must be charged before each use (USB Charge Cable included)

•    Indicator light will turn off once fully charged

•    Install batteries in remote

Insert antena through hole at the base of the 

Smart Phone Mount.

Align hole on Mount with hole in antena. Insert 

screw to secure Mount to remote. 

Carefully slide phone into Mount by pulling up 

on top of Mount. Adjust angle accordingly.

Fig. 1

v.06

(Fig. 1)

LAND

LIVE VIDEO STREAMING COVENTRY AVIATION DRONE

LIVE VIDEO STREAMING COVENTRY AVIATION DRONE

LIVE VIDEO STREAMING COVENTRY AVIATION DRONE

LIVE VIDEO STREAMING COVENTRY AVIATION DRONE

LIVE VIDEO STREAMING COVENTRY AVIATION DRONE

LIVE VIDEO STREAMING COVENTRY AVIATION DRONE

• Do not mix old and new batteries

• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries

• Alkaline batteries are recommended. Use only the specified voltage.

• Insert batteries using the correct polarity. Always use, replace, and recharge(if 

  applicable) batteries under adult supervision.

• Do not charge with non-rechargeable batteries.

• Do not short-circuit the supply terminal.

• Do not dispose of batteries in fire, batteries may explode or leak.

• Remove batteries before storing.

• Recycle or dispose of batteries according to federal, state, and local laws.

Alkaline Battery Warning:

Rechargeable Battery Warning:

• This product contains batteries that non-replaceable.

• There is a risk of fire and personal injury if battery is punctured, damaged 

   or misused.

•  Do not dismantle, crush, incinerate or short-circuit battery.

•  Never expose battery to extreme temperatures or moisture.

•  Keep away from flammable materials and direct sunlight.

•  Only charge using the provided charger, cable, and/or adapters.

•  Rechargeable battery is only to be charged by an adult.

•  Adult Supervision of the battery while it is charging is required

•  Allow battery to cool to room temperature before charging.

•  Charge on a non-flammable surface and keep away from flammable products

•  Discontinue charging if battery becomes hot, swells, smokes, or gives off 

   a strong odor.

•  Battery chargers used with the product are to be regularly examined for 

   damage to the cord, plug, enclosure, and other parts, and in the event of 

   such damage, they must not be used until the damage has been repaired.

•  Recycle or dispose of battery according to federal, slate, and local laws

•  Keep these instructions for future reference.

 

LIVE VIDEO STREAMING COVENTRY AVIATION DRONE

LIVE VIDEO STREAMING COVENTRY AVIATION DRONE

LIVE VIDEO STREAMING COVENTRY AVIATION DRONE