Develco Products HMSZB110 User Manual
eng
Quelle: http://www.barcode-generator.de
3. Release the button.
4. Resetting process is complete when the
4. Resetting process is complete when the
LED starts to blink.
Other information
• Do not paint the sensor.
• Dispose the product and battery properly
• Dispose the product and battery properly
at the end of life. This is electronic waste
which should be recycled.
which should be recycled.
Fault finding & cleaning
• In case of a bad or wireless weak signal,
change the location of the Humidity Sensor.
Otherwise you can relocate your gateway
or strengthen the signal with a smart plug.
Otherwise you can relocate your gateway
or strengthen the signal with a smart plug.
Battery replacement
• Open the casing of the Humidity Sensor to
replace the batteries.
• Replace the batteries respecting the
polarities.
• Close the casing of the sensor.
CAUTION: When removing cover for battery
change - Electrostatic Discharge (ESD) can
harm electronic components inside
change - Electrostatic Discharge (ESD) can
harm electronic components inside
Resetting
Resetting is needed if you want to connect
your Humidity Sensor to another gateway or
if you need to perform a factory reset to avoid
abnormal behavior.
your Humidity Sensor to another gateway or
if you need to perform a factory reset to avoid
abnormal behavior.
STEPS FOR RESETTING
1. Open the casing of the Humidity Sensor.
2. Press and hold the button until the LED
2. Press and hold the button until the LED
flashes continuously.
Installation
1. Open the casing of the Humidity Sensor
and remove the batteries.
DO NOT PLACE THE SENSOR
• On the ceiling
• Behind obstacles, e.g. curtains.
• Under direct sunlight or bright light.
• Close to radiators.
• Close to electromagnetic fields.
• Behind obstacles, e.g. curtains.
• Under direct sunlight or bright light.
• Close to radiators.
• Close to electromagnetic fields.
Placement
PLACE THE SENSOR
• Indoors at a temperature between 0-50°C.
• In a room, where it is necessary to detect
humidity.
• On a wall, where it is reachable for the
battery testing and maintenance.
• Insert two AA batteries respecting the
polarities.
NOTE: Do not remove the product label as it
contains important information.
contains important information.
Getting started
• Open the sensor by pushing the switch and
pulling the top of the casing.
Product description
Humidity Sensor allows you to protect your
building and belongings by monitoring the
temperature and humidity levels in any room,
and receive immediate alerts if the climate
fluctuates to unsafe levels.
building and belongings by monitoring the
temperature and humidity levels in any room,
and receive immediate alerts if the climate
fluctuates to unsafe levels.
By supervising the indoor climate, the wireless
Humidity Sensor helps maintain the ideal
comfort level and protect interior, electronics,
musical instruments, furniture, artwork, and
any other humidity-sensitive household item.
Humidity Sensor helps maintain the ideal
comfort level and protect interior, electronics,
musical instruments, furniture, artwork, and
any other humidity-sensitive household item.
Version 1.3
INSTALLATION MANUAL
Product reference HMSZB-110
Humidity Sensor
• The Humidity Sensor will start searching
(up to 15 minutes) for a ZigBee network to
join.
join.
• Make sure that the ZigBee network is open
for joining devices and will accept this
Humidity Sensor.
Humidity Sensor.
• If the scanning has timed out, a short press
on the button will restart it.
Develco Products assumes no responsibility
for any errors, which may appear in this
manual.Furthermore, Develco Products
reserves the right to alter the hardware,
software, and/or specifications detailed
herein at any time without notice, and Develco
Products does not make any commitment to
update the information contained herein. All
the trademarks listed herein are owned by
their respective owners.
for any errors, which may appear in this
manual.Furthermore, Develco Products
reserves the right to alter the hardware,
software, and/or specifications detailed
herein at any time without notice, and Develco
Products does not make any commitment to
update the information contained herein. All
the trademarks listed herein are owned by
their respective owners.
Distributed by Develco Products A/S
Olof Palmes Allé 40
8200 Aarhus
Denmark
Olof Palmes Allé 40
8200 Aarhus
Denmark
All rights reserved.
2. Use double-sided tape or screws to attach
the sensor on the wall.
4. Make sure that the Humidity Sensor has
joined a network before closing the casing.
NOTE: Be aware that electronics are sensitive
to static electricity, so aim to discharge before
touching, and avoid touching any components
inside the device.
to static electricity, so aim to discharge before
touching, and avoid touching any components
inside the device.
3. Insert batteries respecting the polarities.
50 cm
150 cm
WALL