YFC-BonEagle ELECTRIC CO. LTD. TXL16 User Manual

Each Box Contains:

1 Laser Light Projector

2 Piece Ground Stake (x2)

1 Remote Control (3V CR2032 Battery Included)

1 Remote Control Holder

2 Screws to mount Remote Control Holder

1 Instruction Manual
Required Tool:

Small Phillips Screwdriver (not included)

This product contains a built-in heater to protect the laser

diodes (light source) from freezing. The heater must

continue to receive power even when the light is turned off.

Failure to maintain the electrical power to this product when

temperatures drop below 32°F can cause permanent failure

of the laser diodes.

It may take up to 10 minutes after the laser has been turned

on for it to achieve full brightness.

SET-UP INSTRUCTIONS

PROGRAMMING INSTRUCTIONS

WARNING

Once plugged in, select your pattern and countdown time

and the Prime Laser Projector will automatically repeat

every day at dusk with your selected settings!
You may change settings on the laser with the remote

control or by using the buttons on the laser projector base.
A plastic stake is provided for in ground use.

KEY FEATURES

1. Twist the 2 black stake parts together

clockwise to make one long stake.

(Fig. 1)

2. Attach the long stake to the base of

the Laser Light Projector by twisting

clockwise. (Fig. 2)

3. Push the stake into the ground

leaving the top half of the stake

(6 inches) exposed. Do not use

the laser unit itself to insert the stake

into the ground. (Fig. 3)

4. Plug the unit into a GFCI protected

outlet.

5. Use the angle adjustment knob

located between the head of the

Laser Light Projector and the base to

adjust the laser to the desired angle.

(Fig. 4)

6. Remove clear plastic tab from the

battery compartment before use.

To replace the battery in the remote

control, use a small Phillips

screwdriver to remove the screw

that secures the battery compartment

cover on the back of the remote

control. The screw loosens by

turning it counterclockwise. (Fig. 5)

To open the plastic battery

compartment cover twist the battery

compartment cover counterclockwise with a coin or

other flat tool, aligning the arrow on the cover to the

UNLOCKED symbol, (Fig. 6). Remove the plastic cover

over the button cell battery to activate it or before

installing a replacement CR2032 button cell battery.

Make sure the negative side (-) of the battery faces

inward and the positive side (+) faces outward (Fig. 7).

Once the new battery is in place, align the arrow on the

cover with the UNLOCKED

symbol on the back of the

remote. Use a coin or other flat

tool to twist the battery

compartment cover to the right to

align with the LOCKED symbol.

To secure the battery

compartment place the small

screw back into the designated

hole in the battery compartment

and tighten it by turning it

clockwise. (Fig 8)

7. For easy access and storage of

the remote control, we’ve

included a holder that may be

wall-mounted. Mount the remote

control holder to a flat surface or

a wall and secure it with the two

screws that are included. (Fig 9)

Fig. 1

Fig. 2

Fig. 7

Fig. 4

Fig. 5

Fig. 6

Plug the laser into an outdoor rated

GFCI receptacle.

NOTE: When you first plug in the laser

• The default settings are:

• Light Color: Red & Green Mode

• Timer: 6 hours

• The laser light color may be

adjusted/set from either the top

button on the laser base labeled

“Mode” (Fig 10) or from the buttons

on the remote control.

• The time setting may be changed

either by pressing the bottom button

on the laser body labeled “Timer” or

from the buttons on the remote

control.

1. The laser will automatically turn on

at dusk each day and run for the

time programmed. It may take up to

10 minutes before the laser reaches

full brightness.

IMPORTANT NOTE: Once you

have plugged in the laser to start

using it, do not unplug it until

done using it in that location.

2. There are 3 different color display

options to choose from: RED &

GREEN (default), GREEN ONLY or

RED ONLY.

a. RED & GREEN MODE

i. As mentioned, when the laser

is first plugged into an outlet,

this is the default setting.

ii. To select the RED & GREEN

color mode by using the

remote control, press the button to turn on the

laser. Press the R&G color mode button on the

remote control. Allow the laser to run through the

programmed timer setting or press the button

again to turn OFF the laser until it automatically

turns on at dusk.

iii. To manually select this mode, press the "Mode"

button on the base of the laser (Fig. 10) until the

laser projects red & green light. The laser must

run through a full timer cycle, (one night's use) for

the color mode you selected to be saved to repeat

the next night. The color mode will automatically

be saved even when the button on the remote

control is used to manually turn off the laser.

b. GREEN MODE

i. To select the GREEN color mode by using the

remote control, press the button to turn on the

laser. Press the G color mode button on the

remote control. Allow the laser to run through the

programmed timer setting or press the button

again to turn OFF the laser until it automatically

turns on at dusk.

Laser Light

Projector

Model#: CCLFLRGTR05

Item#: 1494311

ENGLISH FRONT-PAGE 1

Fig. 3

ii. To manually select this mode,

press the "Mode" button on the

base of the laser (Fig. 10) until

the laser projects green light.

The laser must run through a

full timer cycle, (one night's

use) for the color mode you

selected to be saved to repeat

the next night. The color mode

will automatically be saved

even when the button on the

remote control is used to

manually turn off the laser.

c. RED MODE

i. To select the RED color mode

by using the remote control,

press the button to turn on

the laser. Press the R color

mode button on the remote

control. Allow the laser to run

through the programmed timer

setting or press the button

again to turn OFF the laser until

it automatically turns on at

dusk.

ii. To manually select this mode,

press the "Mode" button on the

base of the laser (Fig. 10) until

the laser projects red light.

The laser must run through a

full timer cycle, (one night's

use) for the color mode you

selected to be saved to repeat

the next night. The color mode

will automatically be saved

even when the button on the

remote control is used to

manually turn off the laser.

d. POWER OFF

i. To turn off the laser using the

remote control, press the

button. The laser will

automatically turn on again the

next evening at dusk in the last

color and timer modes.

ii. To turn off the laser manually,

press the “Mode” button until

the laser turns OFF. The laser

will automatically turn on again

the next evening at dusk in the

last color mode programmed.

3. There are 4 different timer settings to

choose from:

On at Dusk, off in 2, 4, 6 or 8 hours.

The default setting when the laser projector is first

plugged in is 6 hours.

a. To select the timer setting using the remote control,

first turn the laser ON by pressing the button.

b. Then press the 2h, 4h, 6h or 8h button to select how

long you want the laser to run each night. Press the

Fig. 8

Fig. 9

Fig. 10

2hrs

4hrs

6hrs

8hrs