Transition Networks CETTF1029-106 Leaflet

Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA

tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com

©2010 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.

CETTF10xx-x0x

Specifications

Standards

IEEE Std. 802.3, 10BASE-T; 10BASE-FL

4-position Switch

Fiber Port: Enables / disables network traffic on the
fiber port; (Up = enabled)
Copper Port: Enables / disables network traffic on
the copper port; (Up = enabled)
AutoCross™: Enables / disables AutoCross™
function; (Up = enabled)
Link Pass Through: Enables / disables Link Pass
Through function; (Up = enabled)

3-position Jumper

Hardware: Converter mode is determined by
4-position switch settings
Software: Converter mode is determined by most
recently saved on-board microprocessor setting

Status LEDs

PWR (Power): On for normal operation;
LKF (Link Fiber): Steady LED indicates good fiber
link and normal operation;
RXF (Receive Fiber): Flashing LED indicates data
reception on fiber link;
LKC (Link Copper): Steady LED indicates good
copper link and normal operation;
RXC (Receive Copper): Flashing LED indicates data
reception on copper link

Dimensions

Width: 0.86" [22 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]

Power Consumption

2.3 Watts

Environment

See chassis specifications

Shipping Weight

1 lb. [0.45 kg]

Regulatory Compliance

EN55022; EN55024; EN61000; CE Mark

Warranty

Lifetime

point system™ slide-in-module media converter

Integrate mixed cabling

environments in either
switched or shared
Ethernet networks.

Connect legacy 10BASE-T

devices to a fiber based
cabling infrastructure.

Ordering Info: Class A

CETTF1011-105

10BASE-T (RJ-45)

[100 m/328 ft.]

to 10BASE-FL 850 nm MM (ST)

[2 km/1.2 mi.] Link Budget: 13.5 dB

CETTF1013-105

10BASE-T (RJ-45)

[100 m/328 ft.]

to 10BASE-FL 850 nm MM (SC)

[2 km/1.2 mi.] Link Budget: 13.5 dB

CETTF1027-105

10BASE-T (RJ-45)

[100 m/328 ft.]

to 10BASE-FL 1300 nm MM (ST)

[5 km/3.1 mi.] Link Budget: 13.5 dB

CETTF1012-105

10BASE-T (RJ-45)

[100 m/328 ft.]

to 10BASE-FL 1310 nm SM (ST)

[20 km/12.4 mi.] Link Budget: 7.0 dB

CETTF1014-105

10BASE-T (RJ-45)

[100 m/328 ft.]

to 10BASE-FL 1310 nm SM (SC)

[20 km/12.4 mi.] Link Budget: 15.0 dB

CETTF1022-105

10BASE-T (RJ-45)

[100 m/328 ft.]

to 10BASE-FL 1310 nm SM (ST)

[40 km/24.9 mi.] Link Budget: 19.0 dB

CETTF1015-105

10BASE-T (RJ-45)

[100 m/328 ft.]

to 10BASE-FL 1310 nm SM (SC)

[40 km/24.9 mi.] Link Budget: 14.0 dB

Single Fiber Products
Recommended use in pairs (see page 18)

CETTF1029-105

10BASE-T (RJ-45)

[100 m/328 ft.]

to 10BASE-FL 1310 nm TX / 1550 nm RX

single fiber SM (SC)

[20 km/12.4 mi.] Link Budget: 19.0 dB

CETTF1029-106

10BASE-T (RJ-45)

[100 m/328 ft.]

to 10BASE-FL 1550 nm TX / 1310 nm RX

single fiber SM (SC)

[20 km/12.4 mi.] Link Budget: 19.0 dB

Extend Network Distance

Two 10BASE-T to 10BASE-FL Media
Converters used back-to-back extend the
distance between two 10BASE-T devices
up to 5 km (3.1 mi.) using multimode fiber,
up to 40 km (24.9 mi.) using single mode
fiber without a repeater, or up to 20km
using single strand single mode fiber.

Connect Unlike Devices

Connect your workgroup to a distant server
or a central switch; or extend distances
between like and unlike devices in either
full or half-duplex modes.

AUTO CROSS LINK PASS THRU LINK RESTORE

AUTO

UPGRADE

REMOTE FIRMWARE

10BASE-T to 10BASE-FL

SINGLE

FIBER

FCC & CISPR Class A devices comply with
radiated emissions standards for commercial
applications in the United States (FCC Class A)
and Europe (CISPR Class A).

FCC & CISPR Class B devices comply with
radiated emissions standards for residential
applications in the United States (FCC Class B)
and Europe (CISPR Class B).