Transition Networks CSEFE1022-100 Leaflet
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2009 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
Technical information is subject to change without notice.
Specifications
Standards
IEEE Std. 802.3™
Switches
Switch 1: Link Pass Through on/off
Switch 2: 10Mb or 100Mb operation
Switch 2: 10Mb or 100Mb operation
3-position Jumper
Hardware: Converter mode is determined by DIP
switch settings
Software: Converter mode is determined by most
recently saved on-board microprocessor settings
switch settings
Software: Converter mode is determined by most
recently saved on-board microprocessor settings
Status LEDs
PWR (Power): Lit for normal operation
F-ACT (Fiber Activity): Blinking = data reception
on the fiber link
F-100 (Fiber Speed):
ON = link at 100Mb
F-10 (Fiber Speed):
ON = link at 10Mb
C-ACT (Copper Activity): Blinking = data reception
on the copper link
C-100 (Copper Speed):
ON = link at 100Mb
C-10 (Copper Speed):
ON = link at 10Mb
F-ACT (Fiber Activity): Blinking = data reception
on the fiber link
F-100 (Fiber Speed):
ON = link at 100Mb
F-10 (Fiber Speed):
ON = link at 10Mb
C-ACT (Copper Activity): Blinking = data reception
on the copper link
C-100 (Copper Speed):
ON = link at 100Mb
C-10 (Copper Speed):
ON = link at 10Mb
Dimensions
Width: 0.86" [22 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Power Consumption
3.6 watts
Environment
See chassis specifications
Shipping Weight
1 lb. [0.45 kg]
Regulatory Compliance
CISPR/EN55022 Class A; EN55024; EN60950 Class
A; FCC Class A;
CE Mark
A; FCC Class A;
CE Mark
Warranty
Lifetime
Ordering Info
CSEFE1012-100
10BASE-T or 100BASE-TX (RJ-45)
[100 m/328 ft.]
to 10BASE-FL or 100BASE-FX
1310nm SM (ST)
[20 km/12.4 mi.] Link Budget: 17.0 dB
CSEFE1014-100
10BASE-T or 100BASE-TX (RJ-45)
[100 m/328 ft.]
to 10BASE-FL or 100BASE-FX
1310nm SM (SC)
[20 km/12.4 mi.] Link Budget: 17.0 dB
CSEFE1022-100
10BASE-T or 100BASE-TX (RJ-45)
[100 m/328 ft.]
to 10BASE-FL or 100BASE-FX
1310nm SM (ST)
[40 km/24.9 mi.] Link Budget: 26.0 dB
CSEFE1015-100
10BASE-T or 100BASE-TX (RJ-45)
[100 m/328 ft.]
to 10BASE-FL or 100BASE-FX
1310nm SM (SC)
[40 km/24.9 mi.] Link Budget: 26.0 dB
Single Fiber Products
Recommended use in pairs
Recommended use in pairs
CSEFE1029-100
10BASE-T or 100BASE-TX (RJ-45)
[100 m/328 ft.]
to 10BASE-FL or 100BASE-FX 1310nm TX /
1550nm RX single fiber SM (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
CSEFE1029-101
10BASE-T or 100BASE-TX (RJ-45)
[100 m/328 ft.]
to 10BASE-FL or 100BASE-FX 1550nm TX /
1310nm RX single fiber SM (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
Extend Network Distance
Ethernet
Use the 10BASE-T to 10BASE-FL speed setting
(back-to-back) to extend the distance between two
10BASE-T devices up to 40 km (24.9 mi.) using
single mode fiber without a repeater.
(back-to-back) to extend the distance between two
10BASE-T devices up to 40 km (24.9 mi.) using
single mode fiber without a repeater.
Fast Ethernet
Use the 100BASE-TX to 100BASE-FX setting to ex-
tend the distance between any two 100BASE-TX
devices up to 40 km (24.9 mi.) using single mode
fiber. Or interface directly with a 100BASE-FX com-
pliant port on any device to provide a 100BASE-TX
port interface.
tend the distance between any two 100BASE-TX
devices up to 40 km (24.9 mi.) using single mode
fiber. Or interface directly with a 100BASE-FX com-
pliant port on any device to provide a 100BASE-TX
port interface.
CSEFE10xx-10x
point system™ slide-in-module media converter
Selectable speed setting:
The converter can be set to 10Mbps
or 100Mbps. Both copper and fiber
ports are automatically set to the
same speed.
or 100Mbps. Both copper and fiber
ports are automatically set to the
same speed.
Provides easy migration path:
from 10Mbps to 100Mbps networks
Converts copper to fiber:
to assist with fiber integration into
your copper network
your copper network
Transition Networks speed selectable copper to fiber
Media Converter allows you to extend the distance
between copper based connections with the use of
fiber optic cable. The abilityto select the speed of
converter allows for easy migration from a 10Mbps
network today to a 100Mbps network in the future.
This converter is a true layer 1 device as both the
copper and fiber ports operate at the same speed
setting (i.e. 100BASE-TX to 100BASE-FX).
Media Converter allows you to extend the distance
between copper based connections with the use of
fiber optic cable. The abilityto select the speed of
converter allows for easy migration from a 10Mbps
network today to a 100Mbps network in the future.
This converter is a true layer 1 device as both the
copper and fiber ports operate at the same speed
setting (i.e. 100BASE-TX to 100BASE-FX).
For
10Mbps applications, these devices must be
used in pairs.
used in pairs.
AUTO CROSS LINK PASS THRU LINK RESTORE
AUTO
UPGRADE
REMOTE FIRMWARE
10BASE-T to 10BASE-FL or
100BASE-TX to 100BASE-FX
SINGLE
FIBER
Speed Selectable Media Converter
Features
AutoCross™
Link Pass Through
Automatic Link Restoration
Remote Firmware Upgrade
Supports single mode fiber
Management Features
Report local converter status
to chassis:
• Copper/fiber link status
• Hardware/Software mode
• 10Mb or 100Mb speed setting
• Link Pass Through on/off setting
• Hardware/Software mode
• 10Mb or 100Mb speed setting
• Link Pass Through on/off setting
Write operation includes:
• Enable/disable Link Pass Through
• Set speed to 10Mb or 100Mb
• Set speed to 10Mb or 100Mb
Can be used with any
Point System™ Chassis