Transition Networks C2210-1039 Leaflet

Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA

tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com

©2010 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.

Ordering Info

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1300 nm MM (ST)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1300 nm MM (SC)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1300 nm MM (LC)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1300 nm SM (SC)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1300 nm SM (LC)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1300 nm SM (SC)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1300 nm SM (SC)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1550 nm SM (SC)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1550 nm SM (SC)

10/100BASE-TX (RJ-45) 

to  100Base Open SFP

Single Fiber Products 
Recommended use in pairs 

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1310 nm TX / 1550 nm RX 

single fiber single mode (SC)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1550 nm TX / 1310 nm RX 

single fiber single mode (SC)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1310 nm TX / 1500 nm RX 

single fiber single mode (SC)

10/100BASE-TX (RJ-45) 

to 100BASE-FX 1550 nm TX / 1310 nm RX 

single fiber single mode (SC)

Specifications

Standards

IEEE Std. 802.3

Data Rate

10 Mbps; 100 MBps Layer-2

Max Frame Size

2048 bytes

Frame Buffer Memory

512 Kbits

MAC Address Table

1 K

Switches

SW1: Auto-Negotiation (UP = enabled)
SW2: Forced 100 Mbps/10 Mbps with Auto-Neg. off 
(UP = 100 MBps)
SW3: Forced Full/Half Duplex with Auto-Neg. off  (UP = Full)
SW4: Full/Half Duplex on fiber port (UP = Full)
SW5: AutoCross™ on UTP (UP = enabled)
SW6: Link Pass Through (UP = enabled)

Internal Jumpers

AutoCross™: Enable/Disable

Hardware/Software Jumpers        

Hardware: Mode of operation is determined by the 

settings on the 4-position switch 

Software: Mode of operation is determined by the  
most recently saved on-board microprocessor settings

Status LEDs

FD (Fiber Duplex): ON= Full-duplex on fiber
LACT (Fiber Link/Activity): ON = Fiber Link
PWR (Power): ON = Connection to powered backplane
(TP. Duplex/Link): Yellow = Half duplex,
Green = Full Duplex (TP. Speed): Yellow = 10 Mbps,     
Green = 100 Mbps

Dimensions

Width: 0.86” (22 mm)
Depth: 6.5” (165 mm)
Height: 3.4” (86 mm)

Power Consumption

2.5 Watts, 200mA @ 13.9VDC 

Environment

See chassis specifications

Shipping Weight

1 lb. [.45 kg]

Regulatory Compliance 

CISPR/EN55022 Class A, FCC Class A, CE Mark, EN55024

Warranty

Lifetime

AUTO NEG

AUTO CROSS

Features



Auto-Negotiation of speed and duplex 

on TP port



AutoCross™ on TP port  



Link Pass Through (LPT) 

fault monitoring 



Far-End-Fault (FEF) detection  



Pause (Software Controlled) 



Automatic Link Restoration 



Remote Firmware Upgrade 



Can be used in any 
ION Platform Chassis



Standards based, will link with any 
standard 10/100Base-TX and any 
standard 100Base-FX ports

The ION C2210 device provides an 
interface between 10/100Base-TX ports
and 100Base-FX ports allowing users to
integrated fiber optic cabling into
10/100Base-TX copper environments.



Report converter status to 

chassis management software: 

• TP and Fiber Link Status 
• Hardware switch settings 
• Copper Port Speed 
• TP and Fiber Port Duplex 
• Fault condition



Write operation includes:

• Power on/off device
• Auto-Negotiation enable/disable
• Force 10 Mbps or 100 Mbps 
• Force half or full duplex 
• Select advertising modes when  

Auto-Negotiation is enabled

• LPT enable/disable 
• FEF enable/disable 
• Pause enable/disable 
• AutoCross™ enable/disable 

The following manageable features
are available when used in an ION
Platform chassis along with an ION
Management Module.

Fiber Integration

LINK PASS THRU

FAR END FAULT LINK RESTORE

AUTO

PAUSE

UPGRADE

REMOTE FIRMWARE

SINGLE 

FIBER