Transition Networks CRMFE1029-200 Leaflet
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2009 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
AUTO NEG
AUTO CROSS LINK PASS THRU FAR END FAULT LINK RESTORE
AUTO
PAUSE
REMOTE MGMT
LOOP BACK
ALLOCATION
BANDWIDTH
UPGRADE
REMOTE FIRMWARE
Specifications
Standards
IEEE Std. 802.3
3-position Jumpers
Jumper (J2): Enable/Disable AutoCross™
Jumper (J6):
Hardware: mode is determined by 4-position
switch settings
Software: mode is determined by most recently
saved on-board microprocessor settings.
Hardware: mode is determined by 4-position
switch settings
Software: mode is determined by most recently
saved on-board microprocessor settings.
4 position Switch
Pos 1: Auto-Neg: (ON) Advertises 100Mb/s
full/half-duplex during auto-negotiation; (OFF)
(Used primarily when connecting to hub) Operates
at 100Mb/s in duplex mode of attached device.
Pos 2: PAUSE: Applies only if Switch 1 is UP AND
device is connected to Auto-Negotiating device(s)
capable of Pause Control Frame propagation. (UP)
ALLOWS negotiation of Pause Control Frame.
(DOWN) Does NOT allow negotiation of Pause
Control Frame.
Pos 3: Link Pass Through: (UP) enabled;
(DOWN) disabled
Pos 4: Far-End-Fault: (UP) enabled;
(DOWN) disabled
full/half-duplex during auto-negotiation; (OFF)
(Used primarily when connecting to hub) Operates
at 100Mb/s in duplex mode of attached device.
Pos 2: PAUSE: Applies only if Switch 1 is UP AND
device is connected to Auto-Negotiating device(s)
capable of Pause Control Frame propagation. (UP)
ALLOWS negotiation of Pause Control Frame.
(DOWN) Does NOT allow negotiation of Pause
Control Frame.
Pos 3: Link Pass Through: (UP) enabled;
(DOWN) disabled
Pos 4: Far-End-Fault: (UP) enabled;
(DOWN) disabled
Status LEDs
Power
LKF (Fiber Link)\
RXF (Fiber Receive)
RXC (Copper Receive)
LKC (Copper Link)
LKF (Fiber Link)\
RXF (Fiber Receive)
RXC (Copper Receive)
LKC (Copper Link)
Dimensions
Width: 0.86" [22 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Power Consumption
3.4 watts
Environment
See chassis specifications
Shipping Weight
1 lb. [0.45 kg]
Regulatory Compliance
CISPR/EN55022 Class A & B + EN55024; FCC
Class A & B; CE Mark
Class A & B; CE Mark
Warranty
Lifetime
Ordering Info
CRMFE1011-200
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1300nm MM (ST)
[2 km/1.2 mi.] Link Budget: 11.0 dB
CRMFE1013-200
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1300nm MM (SC)
[2 km/1.2 mi.] Link Budget: 11.0 dB
CRMFE1014-200
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1310nm SM (SC)
[20 km/12.4 mi.] Link Budget: 16.0 dB
CRMFE1015-200
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1310nm SM (SC)
[40 km/24.9 mi.] Link Budget: 26.0 dB
CRMFE1016-200
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1310nm SM (SC)
[60 km/37.3 mi.] Link Budget: 29.0 dB
CRMFE1017-200
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1550nm SM (SC)
[80 km/49.7 mi.] Link Budget: 29.0 dB
CRMFE1035-200
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1550nm SM (SC)
[120 km/74.6 mi.] Link Budget: 36.0 dB
Single Fiber Products
Recommended use in pairs
Recommended use in pairs
CRMFE1029-200
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1310nm TX / 1550nm RX sin-
gle fiber SM (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
CRMFE1029-201
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1550nm TX / 1310nm RX sin-
gle fiber SM (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
CRMFE1029-202
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1310nm TX / 1550nm RX sin-
gle fiber SM (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
CRMFE1029-203
100BASE-TX (RJ-45)
[100 m/328 ft.]
to 100BASE-FX 1550nm TX / 1310nm RX sin-
gle fiber SM (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
CRFME10xx-20x
point system™ slide-in-module network interface device
With the Remotely Managed Fast Ethernet NID,
service providers can now monitor and manage
the entire optical link from the Central Office (CO)
to the Customer Premise Equipment (CPE). They
also have the ability to remotely change the
bandwidth offered to the customer in increments
of 64KBps and choose the appropriate mode of
connection straight from their Network
Management Centers.
service providers can now monitor and manage
the entire optical link from the Central Office (CO)
to the Customer Premise Equipment (CPE). They
also have the ability to remotely change the
bandwidth offered to the customer in increments
of 64KBps and choose the appropriate mode of
connection straight from their Network
Management Centers.
Devices should be used in pairs. Typical instal-
lation will include a chassis card installed in the
Point System™ locally and a stand-alone device
(SRMFE pg. 81) installed at the remote location.
lation will include a chassis card installed in the
Point System™ locally and a stand-alone device
(SRMFE pg. 81) installed at the remote location.
Fast Ethernet 100BASE-TX to 100BASE-FX
with Remote Management & Bandwith Allocation
Remotely Managed Fast Ethernet NID
(Network Interface Device)
(Network Interface Device)
Features
Auto-Negotiation
AutoCross™
Link Pass Through
Far-End-Fault (FEF)
Automatic Link Restoration
Pause
Remote Management
Loopback
Bandwidth Allocation
Jumbo Frame Support
Remote Firmware Upgrade
Can be used with any Point System™ Chassis
Remotely Managed Fast Ethernet
In-band management of stand
alone Fast Ethernet NID
alone Fast Ethernet NID
Remote Loopback assists in
diagnosing network problems
diagnosing network problems
Upstream and downstream
Bandwidth Control allows
service providers to offer an
array of services
service providers to offer an
array of services