Transition Networks S6210-3016 S6210-3016-NA Leaflet

Product codes

S6210-3016-NA

Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA

tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com

©2011 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.

Specifications

Standards

ANSI, ITU-TS, ETSI, G.823 for jitter tolerance,
G.755 for loss of signal

Coax Connectors

75 ohm coax

Fiber Connectors

SFP: LC connector Uses standard 100BASE-X/OC-3 SFP
Fixed Optics: ST or SC connector

Data Rates

DS3/T3 = 44.7Mbps; E3 = 34.4Mbps

Status LEDs

Power, Coax link status, coax loop-back status, AIS on coax
link; Fiber link status, fiber loop-back status, AIS on fiber link

Dimensions

W: 3.5” [82 mm]; D: 6.5” [165 mm]; H: 1.0” [25 mm]

Power Consumption

2.4 Watts

Power

Input: 100-240 VAC
Output: 12 VDC

Operating Temp

-10°C to 65°C

Altitude

0-10,000 Feet

Operating Humidity

5-95% (non-condensing)

Shipping Weight

2.0 lbs. [0.90 kg]

Regulatory Compliance

CISPR/EN55022 Class A; FCC Class A; CE Mark, UL60950

MTBF w/Power Supply

Greater than 41,660 hours (MIL-HDBD-217F)
Greater than 114,580 hours (Bellcore)

MTBF w/o Power Supply

Greater than 250,000 hours (MIL-HDBD-217F)
Greater than 687,000 hours (Bellcore)

Warranty

Lifetime

DS3 – T3/E3 Coax to Fiber Network Interface Device

Features

AIS (Alarm Indication Signal)

Coax Line Build Out

Switch selectable for DS3/T3 or E3

Remote firmware upgrade

Loopback – Coax and Fiber

LEDs for immediate visual status

Supports dual or single fiber

Supports multimode and single mode

fiber at a variety of distances

Supports CWDM SFPs

SNMP management when used with

ION chassis and management module

Remote standalone can be managed

by local peer

The DS3 – T3/E3 copper to fiber network
interface device (NID) provides a solution
for those users that need to extend DS3
connections over fiber.

The DS3 – T3/E3s supports Small Form
Pluggable (SFP) transceivers to support a
variety of fiber types, distances and
wavelengths to provide maximum flexi-
bility across a variety of network topolo-
gies. The use of Coarse Wave Division
Multiplexing (CWDM) SFPs can be utilized
to further increase the bandwidth capac-
ity of the fiber infrastructure.

The DS3 – T3/E3 NID must be used in
pairs. A typical installation will include a
chassis card installed in the ION Platform
locally and a stand-alone device installed
at the remote location.

Integrate Voice & Data on Fiber Network

S6210 Series

stand-alone device for the ion platform

DS3 – T3/E3

The ION Platform

Ordering Information

S6210-3011

(2) Coax (BNC)

to 1300nm multimode (ST)

[2 km/ 1.2 mi.] Link Budget: 11.0 dB

S6210-3013

(2) Coax (BNC)

to 1300nm multimode (SC)

[2 km/ 1.2 mi.] Link Budget: 11.0 dB

S6210-3014

(2) Coax (BNC)

to 1310nm single mode (SC)

[20 km/12.4 mi.] Link Budget: 16.0 dB

S6210-3015

(2) Coax (BNC)

to 1310nm single mode (SC)

[40 km/24.9 mi.] Link Budget: 29.0 dB

S6210-3016

(2) Coax (BNC)

to 1310nm single mode (SC)

[60 km/37.3 mi.] Link Budget: 32.0 dB

S6210-3017

(2) Coax (BNC)

to 1550nm single mode (SC)

[80 km/49.7 mi.] Link Budget: 29.0 dB

S6210-3040

(2) Coax (BNC)

to SFP slot (empty)

Single Fiber Products

Recommended use in pairs

S6210-3029-A1

(2) Coax (BNC)

to 1310nm TX/1550nm RX single fiber

single mode (SC)

[20 km/12.4 mi.] Link Budget: 19.0 dB

S6210-3029-A2

(2) Coax (BNC)

to 1550nm TX/1310nm RX single fiber

single mode (SC)

[20 km/12.4 mi.] Link Budget: 19.0 dB

S6210-3029-B1

(2) Coax (BNC)

to 1310nm TX/1550nm RX single fiber

single mode (SC)

[40 km/24.9 mi.] Link Budget: 25.0 dB

S6210-3029-B2

(2) Coax (BNC)

to 1550nm TX/1310nm RX single fiber

single mode (SC)

[40 km/24.9 mi.] Link Budget: 25.0 dB