Transition Networks SCSCF3016-110 SCSCF3016-110-NA Leaflet
Product codes
SCSCF3016-110-NA
LOOP BACK
Specifications
Standards
ANSI, ITU-TS, ETSI, AT&T, G.703, G.921 & G.955
Coax Connectors
75 ohm coax
TX output
TX output
RX input
min: +2.5 dBm
min: -9.7dBm
max: +9.1 dBm
max: +10.5 dBm
Fiber Connectors
SFP: LC connector Uses standard 100BASE-X/OC-3 SFP
Data Rates
DS3/T3 = 44.7 Mbps; E3 = 34.4 Mbps;
STS-1 = 51.8 Mbps
STS-1 = 51.8 Mbps
Status LED
Power, Coax link status, coax loop-back status, AIS on coax
link; Fiber link status, fiber loop-back status,
AIS on fiber link
link; Fiber link status, fiber loop-back status,
AIS on fiber link
Dimensions
Width: 3.25" [83 mm];
Depth: 4.7" [119 mm];
Height: 1.0" [25 mm]
Depth: 4.7" [119 mm];
Height: 1.0" [25 mm]
Power Consumption
3.0 Watts
Power Supply
12 VDC, 0.8 Amp (minimum)
Environment
Operating Temperature 0º to 50ºC (32º to 122ºF)
Humidity 5-95% non-condensing
Storage Temperature -20º to 85ºC (-4º to 185ºF)
Humidity 5-95% non-condensing
Storage Temperature -20º to 85ºC (-4º to 185ºF)
Shipping Weight
2.0 lbs. [0.90 kg]
Regulatory Compliance
CISPR/EN55022 Class A; FCC Class A; CE Mark
MTBF w/ Power Supply
Greater than 41,660 hours (MIL-HDBD-217F)
Greater than 114,580 hours (Bellcore)
Greater than 114,580 hours (Bellcore)
MTBF w/o Power Supply
Greater than 250,000 hours (MIL-HDBD-217F)
Greater than 687,000 hours (Bellcore)
Greater than 687,000 hours (Bellcore)
Warranty Lifetime
SCSCF30xx-11x
stand-alone network interface device
DS3-T3/E3 and STS-1 Coax to Fiber
DS3-T3/E3 and STS-1 Coax to Fiber NID
see also:
DS3-T3/E3 Point System™ Slide-In-Module NID
The DS3 – T3/E3 & STS-1 copper to fiber network
interface device (NID) provides a solution for those
users that need to extend DS3 connections over fiber.
interface device (NID) provides a solution for those
users that need to extend DS3 connections over fiber.
The DS3 – T3/Es & STS-1 supports Small Form Plug-
gable (SFP) transceivers to support a variety of fiber
types, distances and wavelengths to provide maxi-
mum flexibility across a variety of network topolo-
gies. The use of Coarse Wave Division Multiplexing
(CWDM) SFPs can be utilized to further increase the
bandwidth capacity of the fiber infrastructure.
gable (SFP) transceivers to support a variety of fiber
types, distances and wavelengths to provide maxi-
mum flexibility across a variety of network topolo-
gies. The use of Coarse Wave Division Multiplexing
(CWDM) SFPs can be utilized to further increase the
bandwidth capacity of the fiber infrastructure.
The DS3 – T3/E3 & STS-1 NID must be used in pairs*.
A typical installation will include a chassis card in-
stalled in the Point System™ locally and a stand-
alone device installed at the remote location.
alone device installed at the remote location.
DS3-T3/E3
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2010 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
Ordering Information
SCSCF3011-110
(2) Coax (BNC)
to 1300nm multimode (ST)
[2 km/ 1.2 mi.] Link Budget: 14.0 dB
SCSCF3013-110
(2) Coax (BNC)
to 1300nm multimode (SC)
[2 km/ 1.2 mi.] Link Budget: 14.0 dB
SCSCF3014-110
(2) Coax (BNC)
to 1310nm single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
SCSCF3015-110
(2) Coax (BNC)
to 1310nm single mode (SC)
[40 km/24.9 mi.] Link Budget: 29.0 dB
SCSCF3016-110
(2) Coax (BNC)
to 1310nm single mode (SC)
[60 km/37.3 mi.] Link Budget: 32.0 dB
SCSCF3017-110
(2) Coax (BNC)
to 1550nm single mode (SC)
[80 km/49.7 mi.] Link Budget: 29.0 dB
SCSCF3040-110
(2) Coax (BNC)
to SFP slot (empty)
Single Fiber Products
Recommended use in pairs
SCSCF3029-110
(2) Coax (BNC)
to 1310nm TX/1550nm RX single fiber
single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
SCSCF3029-111
(2) Coax (BNC)
to 1550nm TX/1310nm RX single fiber
single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
SCSCF3029-112
(2) Coax (BNC)
to 1310nm TX/1550nm RX single fiber
single mode (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
SCSCF3029-113
(2) Coax (BNC)
to 1550nm TX/1310nm RX single fiber
single mode (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
SCSCF3029-114
(2) Coax (BNC)
to 1310nm TX/1550nm RX single fiber
single mode (SC)
[40 km/37.3 mi.] Link Budget: 29.0 dB
SCSCF3029-115
(2) Coax (BNC)
to 1550nm TX/1310nm RX single fiber
single mode (SC)
[60 km/37.3 mi.] Link Budget: 29.0 dB
SCSCF3029-116
(2) Coax (BNC)
to 1310nm TX/1550nm RX single fiber
single mode (SC)
[80 km/49.7 mi.] Link Budget: 33.0 dB
SCSCF3029-117
(2) Coax (BNC)
to 1550nm TX/1310nm RX single fiber
single mode (SC)
[80 km/49.7 mi.] Link Budget: 32.0 dB
*The SCSCF3040-110 will only work with
another CCSCF3040-110 or SCSCF3040-110.
The product does not work with a -10x model.
another CCSCF3040-110 or SCSCF3040-110.
The product does not work with a -10x model.
Optional Accessories
(sold separately)
Wide Input (24 – 60 VDC) Power Supplies:
SPS-2460-PS
Piggy Back Power Supply
SPS-2460-SA
Stand-Alone Power Supply
Mounting Options:
E-MCR-05
12-Slot Media Converter Rack
WMBD
DIN Rail Bracket 5.0" [127 mm]
WMBD-F
DIN Rail Bracket (flat) 3.3" [84 mm]
WMBL
Wall Mount Bracket 4.0" [102 mm]
WMBV
Vertical Wall Mount Bracket 5.0" [127 mm]
RMS19-SA4-01
4-Slot Media Converter Shelf
Features
AIS (Alarm Indication Signal)
Coax Line Build Out
Switch selectable for DS3/T3 or E3
Loopback – Coax and Fiber
LEDs for immediate visual status
Supports dual or single fiber
Supports multimode and single mode
fiber at a variety of distances
Supports CWDM SFPs
Integrate Voice & Data on Fiber Network