Spaun SBK 5503 NFI 842488 User Manual
Product codes
842488
56
www.spaun.com
SA
T IF
SA
T IF
Premium-Class
UNiSEqC Single Cable System 5 in 3x3 or 1x8 according to EN 50494
SUS 5581/33 NF LEGACY, SUS 5581/33 NFA LEGACY
The new Premium product SUS 5581/33 NF LEGACY offers
users pure single-cable operation according to EN 50494, with
an option of 1x8 or 3x3 subscribers. With the 1x8 operating
mode, the two unused outputs are now also available as pure
“legacy outputs”. This means that the device can also be used
as a conventional multiswitch.
users pure single-cable operation according to EN 50494, with
an option of 1x8 or 3x3 subscribers. With the 1x8 operating
mode, the two unused outputs are now also available as pure
“legacy outputs”. This means that the device can also be used
as a conventional multiswitch.
Thanks to the SUS 5581/33 NFA LEGACY design, the device
additionally boasts active SAT trunk lines.
This allows the realisation of cost-effective cascade distribution
systems that operate without a base amplifier in good reception
conditions.
additionally boasts active SAT trunk lines.
This allows the realisation of cost-effective cascade distribution
systems that operate without a base amplifier in good reception
conditions.
SAT IF:
• SCR multiswitch for the distribution of 4
SAT IF positions and terrestrial by one output to max. 8
receiver or by 3 outputs to max. 3 receiver
• Active SAT trunk lines (only SUS 5581/33 NFA LEGACY)
• In the 1x8 operating mode, the two unused outputs
• In the 1x8 operating mode, the two unused outputs
can be used as standard multiswitch outputs
(Legacy mode)
• The selection of the SAT IF position is affected
by the receiver through a specific DiSEqC
TM
command according to EN 50494
• No limitation on transponder reception
• LNB-Mode selectable to use a Quattro- or a QUAD-LNB
• All subscriber outputs are automatic gain controlled
• Multipurpose LED status notification
• Delivery including wall power supply SNG 18/1000
• LNB-Mode selectable to use a Quattro- or a QUAD-LNB
• All subscriber outputs are automatic gain controlled
• Multipurpose LED status notification
• Delivery including wall power supply SNG 18/1000
Terrestrial:
• The terrestrial input is passive
• The reception of the terrestrial signal is also possible
• The reception of the terrestrial signal is also possible
1 x 8
3 x 3
Output mode switch:
• 1 x 8 (1 output with 8 receiver)
(Legacy Mode for unused outputs)
• 3 x 3 (3 outputs with 3 receiver)
(Legacy Mode for unused outputs)
• 3 x 3 (3 outputs with 3 receiver)
LNB supply voltage
switch for Quattro- or
QUAD-LNB
switch for Quattro- or
QUAD-LNB
12 V
22 kHz
18 V
12 V
22 kHz
18 V
Always On
Standby
LNB Mode
when the SAT-receivers are switched off
• Remote power over terrestrial trunkline possible
The multiswitch provides 2 operation modes:
1. The input signals are feeded in one ouput.
On this ouput the connection of max. 8 receiver
is possible. The two unused outputs can be used
as conventional multiswitch outputs
(Legacy Mode).
2. By switching to the second operation mode, the
input signals will be feeded into 3 outputs. On
each output the connection of max. 3 receiver is
possible
The device has an internal protection circuit to
shut down if no DiSEqC command according
to EN 50494 is sent. The use of special TV
socket outlets with such a protection circuit is
not necessary.
shut down if no DiSEqC command according
to EN 50494 is sent. The use of special TV
socket outlets with such a protection circuit is
not necessary.
Tech Hint
Active SAT trunk lines
(only SUS 5581/33 NFA LEGACY)
LED:
Unused outputs in Legacy
Mode (1x8)
Mode (1x8)
Standby Function and
Switch-Mode Power Supply
Energy
Saver!
Meaning
LED
Remote voltage 13 V
green
Valid command being executed
green flashing
Short circuit
red
Remote voltage 5 .. 10 V
red flashing
Remote voltage > 15 V
orange
Band
orange flashing