Cisco T3 kit CAB-T3-KIT17= User Manual
Product codes
CAB-T3-KIT17=
Page 3 of 28
78-19803-02 Cisco TelePresence System T3 System Assembly Guide, December 2011
Related documents
The following documents are also available:
•
T3 Room Recommendations Guide 119076
•
Maintenance Guide: 78-19801
•
Cable Schematics: 78-19798
•
Room Installation Guide: 78-19802
•
Quick User Reference Guide: 78-19804
•
Document Camera Assembly Guide: 78-19800
•
Ceiling Lights Assembly Guide: 78-19799
With the exception of the Room Recommendations Guide
all of these documents are supplied with the Systems
they describe. Should you nevertheless need any of these
documents, contact your Cisco partner.
all of these documents are supplied with the Systems
they describe. Should you nevertheless need any of these
documents, contact your Cisco partner.
What has changed?
General:
•
The removal of the splitter in the left system bottom
module has caused changes in the cabling structure
descriptions. This is reflected in revised cable structure
drawings and corresponding tables.
module has caused changes in the cabling structure
descriptions. This is reflected in revised cable structure
drawings and corresponding tables.
•
The presentation monitor assembly installation
procedure has been changed in this version.
procedure has been changed in this version.
•
Revised description of bottom module assembly
procedure. Recommended sequence is to start with
the innermost (the right) module—as viewed from the
recommended door location. It used to be the left module.
procedure. Recommended sequence is to start with
the innermost (the right) module—as viewed from the
recommended door location. It used to be the left module.
•
Ceiling light assembly is now moved to a separate
document.
document.
•
Document camera installation is now a separate
document
document
Additions, changes and updates
•
Illustrations showing the need for keeping the distance
between the table and the rear wall at 130 cm.
between the table and the rear wall at 130 cm.
•
Fastening the left bottom module.
•
Drawing describing splitter bracket mounting in right
bottom module.
bottom module.
•
Drawing showing revised floor cabling structure.
•
Drawings showing monitors when mounting now shows
monitors without grilles attached.
monitors without grilles attached.
•
Drawing showing revised system cabling structure.
•
Drawing showing how the TCU is mounted in left table
column.
column.
•
Drawing showing revised table cabling structure.
•
Description of the presentation monitor assembly
installation.
installation.
•
Fire enclosure for document camera associated
equipment.
equipment.
•
Drawing showing document camera location.
•
Change in the document camera cabling.
•
Description of document camera installation.
•
Trip lists are now an integral part of the cover plates and
need no mounting description.
need no mounting description.
•
Drawing of the cover plates.
Tools needed
You will need the following tools and equipment when
assembling the system:
assembling the system:
•
Spirit Leve
l (bubble level) for light installation and
monitor levelling.
•
13 mm open end/box wrench
to fasten bottom
module to steel structure, columns to steel structure,
table to columns.
table to columns.
•
10 mm open end wrench
to fasten floor structure
center to left/right, adjusting table top tighteners,
codec brackets to bottom module, adjusting TCU,
Splitter, Switch and Power brackets, cleaning kit and
doc pockets, fasten center cover plates.
codec brackets to bottom module, adjusting TCU,
Splitter, Switch and Power brackets, cleaning kit and
doc pockets, fasten center cover plates.
•
1
⁄
4
” ratchet wrench
•
1
⁄
4
” socket extension
•
13 mm deep socket
to fasten table column to steel
structure and to fasten the table.
•
10 mm socket
to fasten splitter to bottom module,
adjust center door bottom module and fasten table to
columns.
columns.
•
7 mm socket
to dismount screws in bottom module
and monitors (preparing for angle plate between
screens).
screens).
•
5 mm Allen bit
for height adjustment of monitor
systems.
•
4 mm Allen bit
to removing cable hatches in bottom
module, fasten center cover plates.
•
3 mm Allen bit
to mount angle plate between screens.
•
2.5 mm Allen bit
to dismount screws in bottom
module and monitors (preparing for angle plate
between screens)and dismount/mount column covers.
between screens)and dismount/mount column covers.
•
2 mm Allen wrench
for cable clamps in cable wells.
•
Torx T10
to fasten codec brackets to codecs, fasten
cleaning kit and doc pockets.
•
Torx T20
to fasten power outlet brackets in cable wells.
•
Portable drill
•
Hammer
for cable wells power outlets (if installation is
to be done).
•
Blade screwdriver
for cable wells power outlets (if
installation is to be done).
•
1
⁄
4
” deep socket
to fasten cable wells power outlets to
the brackets (if installation is to be done).