Transition Networks C4TEF1014-125 Leaflet

Ordering Information

 

1300nm multimode (ST) 

to 

(4) RJ-48 

 

plus 10/100BASE-TX (RJ-45) 

 

1300nm multimode (SC) 

to 

(4) RJ-48 

 

plus 10/100BASE-TX (RJ-45) 

 

1310nm single mode (SC) 

to 

(4) RJ-48 

 

plus 10/100BASE-TX (RJ-45) 

 

1310nm single mode (SC) 

to 

(4) RJ-48 

 

plus 10/100BASE-TX (RJ-45) 

 

1310nm single mode (SC)

to 

(4) RJ-48 

 

plus 10/100BASE-TX (RJ-45) 

 

1550nm single mode (SC)

to 

(4) RJ-48 

 

plus 10/100BASE-TX (RJ-45) 

 

1550nm single mode (SC) 

to 

(4) RJ-48 

 

plus 10/100BASE-TX (RJ-45) 

 

1 SFP port (Empty) 

to 

(4) RJ-48 

 

plus 10/100BASE-TX (RJ-45) 

 

2 SFP ports (Empty) 

to 

(4) RJ-48 

plus 10/100BASE-TX (RJ-45) 

Recommended use in pairs 

 

1310nm TX/1550nm RX single fiber SM 

(SC) 

to 

(4) RJ-48 

 

1550nm TX/1310nm RX single fiber SM 

(SC) 

to 

(4) RJ-48 

 

1310nm TX/1550nm RX single fiber SM 

(SC) 

to 

(4) RJ-48 

 

1550nm TX/1310nm RX single fiber SM 

(SC) 

to 

(4) RJ-48 

Specifications

Standards 

Ethernet interface:  

IEEE 802.3™-2008 

 

TDM interfaces:  

ANSI T1.102, T1.403 and T1.408 

ITU I.431, G.703,G.736, G.775 and G.823 

ETSI 300-166, 300-233 and TBR 12/13 

AT&T Pub 62411

Switches 

 

Numerous switch settings for line coding, line buildout, loopback  

 

 

(per port), AIS setting, Ethernet port settings: Auto-Negotiation,  

 

 

 

Force speed/duplex and enable Transparent Link Pass Through

Jumper  

Hardware: mode is determined by DIP switch settings 

  

Software: mode is controlled by the most recently saved,  

 

 

on-board microprocessor setting

Dimensions  

Width: 1.72” [44 mm] 

  

Depth: 5.0” [127 mm] 

  

Height: 3.4” [86 mm]

Power Consumption 

3.6 Watts

Environment   

See chassis specifications

Shipping Weight 

1 lb. [0.45 kg]

Regulatory Compliance 

EN55022 Class A, EN55024, CE mark

Warranty  

Lifetime

see also: 

Stand-Alone NID 

4

Low cost transport capability: (4) T1/E1/J1  

     and (1) Ethernet 

4

Target applications include: FTTx, such as Fiber-to-the-  

     Business, Fiber-to-the-Building, Fiber-to-the-MDU, 

     Fiber-to-the-Home and Cell tower backhaul.

4

Copper connections compatible with G.703,    

     AMI/B8ZS/HDB3, 10/100BASE-TX, and RS232 channel;  

     while the optical connection runs at 155Mbps.

4

TDM traffic is not mapped to Ethernet. A hardware- 

     based solution guarantees the constant bit rate of TDM  

     transport without requiring traffic management.  

     Provides physical layer status monitoring and alarm  

     classification functions for Telecom operators to  

   

     manage their fiber optic network and reduce  

     operation and maintenance costs.

*Note: C4TEF cards cannot be used with the 1-Slot Point System™ Chassis .

 Devices must be used in 

pairs. Typical installation will include a chassis card installed in the Point System™  
locally and a  stand-alone device [S4TEF] installed at the remote location.

Features

4

Loopbacks via Test Set  

4

Auto-Negotiation for  

    10/100BASE-TX 

4

AutoCross™ (auto MDI/MDI-X) 

    [

4

Transparent Link Pass Through  

    for Ethernet 

4

Automatic Link Restoration  

    

4

Pause (Flow Control) 

4

Remote Management 

4

Local and Remote Loopback 

4

Remote Fiber Loss Signaling

4

AIS/TAOS

4

LEDs for each data port

4

Settings for line code, line length, 

    local loopback or remote loopback 

    

4

T1/E1/J1 mode settings

4

Local (AUX) Management Interface

4

Access to complete status  

    information on local and remote  

    device

4

Field Upgradeable Firmware  

    

Management Features

4

 Report local device status:

    • Port Status 

    • Device settings & configuration

4

 Local command operations include:

    • Loopback Fiber & T1/E1  

       per channel

    • AIS TX on fiber on loss of copper 

       link &  AIS TX on copper on loss 

       of fiber link

    • Ethernet settings: 

    • Auto-Negotiation Enable/Disable

    • Force speeds and modes on 

       10/100TX 

4

 Remote device status:

    • Port Status

    • Device settings & configuration

4

 Remote Commands:

    • Loopback Fiber & T1/E1  

       per channel

    • AIS TX on fiber on loss of copper 

       link & AIS TX on copper on 

       loss of 

       fiber link

    • Ethernet settings  

       (Software Mode)

    • Force speeds and modes on 

      10/100TX

    • Enable/Disable: Auto- 

       Negotiation; 

       Link  Pass Through; Flow  

       Control; & AutoCross™

Application