Adtran XFP 10G 1550nm 1442940G1C Leaflet
Product codes
1442940G1C
jobAid
D
ESCRIPTION
The 10 Gigabit Ethernet XFP, 1550 nm, Commercial
Temperature (XFP) optical transceiver is a full duplex serial
electric, serial optical device with both transmit and receive
functions contained in a single module. The XFP provides a
high speed serial link at 10 Gb/s. Installed into an appro‐
priate host module, the XFP provides a 10 Gigabit interface
to the supporting system.
Temperature (XFP) optical transceiver is a full duplex serial
electric, serial optical device with both transmit and receive
functions contained in a single module. The XFP provides a
high speed serial link at 10 Gb/s. Installed into an appro‐
priate host module, the XFP provides a 10 Gigabit interface
to the supporting system.
The transmit side of the XFP converts serial NRZ electrical
date at the10 Gb/s line rate to a standard compliant optical
signal. The receive side of the XFP converts the incoming
DC balanced serial NRZ optical data at the 10 Gb/s line rate
into serial electrical data.
date at the10 Gb/s line rate to a standard compliant optical
signal. The receive side of the XFP converts the incoming
DC balanced serial NRZ optical data at the 10 Gb/s line rate
into serial electrical data.
NOTE
To ensure compatibility, refer to the documentation
provided with the host module.
provided with the host module.
The following features are supported on the XFP:
♦
1550 nm optical signals for up to 40 km reach
♦
Case commercial temperature range from 0°C to 70°C
♦
Low power consumption (< 3 W max)
♦
Excellent EMI performance
CAUTION
!
Due to compliance certification requirements, only XFPs
supplied by ADTRAN are to be used with the host module.
ADTRAN cannot certify system integrity with other XFPs.
supplied by ADTRAN are to be used with the host module.
ADTRAN cannot certify system integrity with other XFPs.
Small Form-Factor Pluggable
10 Gigabit Ethernet XFP, 1550 nm,
Commercial Temperature
Operational Specifications
♦
Optical Specifications:
◊
Transmit Wavelength: 1550 nm
◊
Receive Wavelength: 1530 to 1565 nm
◊
Data rate: 9.95 Gb/s to 11.3 Gb/s
◊
Optical transmit level: –1 to +2 dBm
◊
Optical receive level: > –16 dBm
◊
Optical distance: 40 km maximum
◊
Optical connectors: LC
♦
Extended Environmental Support:
◊
Operational temperature range: 0°C to +70°C
◊
Storage temperature range: –40°C to +85°C
◊
Relative humidity to 85%, noncondensing
I
NSTALLATION
Inspect the XFP. If damaged, file a claim with the carrier
and then contact ADTRAN Customer Service.
and then contact ADTRAN Customer Service.
To install the XFP into an appropriate module, complete
the following steps:
the following steps:
1. Insert the XFP into the XFP cage on the circuit board
of the host module with the latch handle facing out‐
ward. Slide the XFP all the way into the receptacle.
ward. Slide the XFP all the way into the receptacle.
NOTE
The latch on the XFP is for removal only. When removing
the XFP, rotate the latch away from the XFP cage until a
physical click occurs. The XFP should slide easily out of the
cage.
the XFP, rotate the latch away from the XFP cage until a
physical click occurs. The XFP should slide easily out of the
cage.
2. Using thumb and forefinger, exert adequate pressure
to ensure the XFP is completely seated in the XFP
cage.
cage.
3. Do not remove the connector plug until the optical
fiber connection is made.
NOTICE
It is recommended that the connector plug remain on
whenever the transceiver optical fiber connector is not
inserted.
whenever the transceiver optical fiber connector is not
inserted.
4. Continue the installation and turn‐up of the host
module using the instructions in the Job Aid provided
with that module, or using the Installation and
Maintenance Practice (I&M), available online at
with that module, or using the Installation and
Maintenance Practice (I&M), available online at
www.adtran.com
.
CLEI: BVL3AFKD_ _
Product P/N: 1442940G1C
Product P/N: 1442940G1C
Issue Date: November 2010
Document P/N: 61442940G1C-22A