Adtran OC-48 SFP 1550/1310nm 1442705PG2 Leaflet
Product codes
1442705PG2
jobAid
D
ESCRIPTION
The Small Form‐Factor Pluggable OC‐48 Bidirectional 1550/1310
nm (Bidirectional SFP) plugs into ADTRAN equipment designed
to accept Small Form‐factor Pluggables (SFPs). Installed into an
appropriate host unit, the Bidirectional SFP provides an OC–48
interface to the supporting system.
nm (Bidirectional SFP) plugs into ADTRAN equipment designed
to accept Small Form‐factor Pluggables (SFPs). Installed into an
appropriate host unit, the Bidirectional SFP provides an OC–48
interface to the supporting system.
NOTE
To ensure compatibility, refer to the documentation provided
with the host module.
with the host module.
The following features are supported on the Bidirectional SFP:
♦
SONET OC–48 compatible (2.488 Gb/s), single‐fiber operation
♦
15 km maximum optical span
CAUTION
!
Due to compliance certification requirements, only SFPs supplied
by ADTRAN are to be used with the host module. ADTRAN
cannot certify system integrity with other SFPs.
by ADTRAN are to be used with the host module. ADTRAN
cannot certify system integrity with other SFPs.
S
PECIFICATIONS
♦
Optical Specifications:
◊
Optical transmit level: 0 dBm to –5 dBm
◊
Optical receive level: –0 dBm to –20 dBm
◊
Transmit Wavelength: 1550 nm
◊
Receive Wavelength: 1310 nm
◊
Optical budget: 14 (±1) dBm
◊
Optical connectors: LC
Small Form-Factor Pluggable OC-48
Bidirectional 1550/1310 nm
♦
Extended Environmental Support:
◊
Operational temperature range: –40°C to +65°C
◊
Storage temperature range: –40°C to +85°C
◊
Relative humidity to 95%, noncondensing
I
NSTALLATION
To install the Bidirectional SFP into an appropriate module,
complete the following steps:
complete the following steps:
1. Inspect the Bidirectional SFP. If damaged, file a claim with
the carrier and then contact ADTRAN Customer Support.
CAUTION
!
Do not remove the protective end cap from the SFP until the fiber
optic cable is ready to be connected.
optic cable is ready to be connected.
2. Insert the Bidirectional SFP into the SFP cage on the module.
Ensure that the manufacturer’s label on the SFP is facing
upward for correct installation.
upward for correct installation.
3. Slide the Bidirectional SFP all the way into the receptacle
until there is an audible “click”.
NOTE
The latch on the SFP is used to remove the SFP from the cage on
the circuit card.
the circuit card.
S
AFETY
AND
R
EGULATORY
C
OMPLIANCE
CAUTION
!
♦
Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
♦
The SFP meets or exceeds all the applicable requirements of
NEBS, Telcordia GR‐63‐CORE, GR‐1089‐CORE, and ETSI EN
300368. The Bidirectional SFP is intended for deployment in
Central Office type facilities, EEEs, EECs, and locations where
the NEC applies (for example, Customer Premises). The SFP is
to be installed in ADTRAN products in Restricted Access
Locations only, and installed by trained service personnel.
NEBS, Telcordia GR‐63‐CORE, GR‐1089‐CORE, and ETSI EN
300368. The Bidirectional SFP is intended for deployment in
Central Office type facilities, EEEs, EECs, and locations where
the NEC applies (for example, Customer Premises). The SFP is
to be installed in ADTRAN products in Restricted Access
Locations only, and installed by trained service personnel.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the userʹs authority to operate this equipment.
could void the userʹs authority to operate this equipment.
CLEI: S00TALDJ__
Product P/N: 1442705PG2
Product P/N: 1442705PG2
Issue Date: October 2010
Document P/N: 61442705PG2-22A