Sony UNIOFL7C2 Leaflet
IR Illuminator
(Images 1)
Vandal Resistant
Outdoor Recessed Dome
UNI-OFL7C2 & UNI-OFL7T2
Security Camera Enclosures
•
Designed for SNC-RZ25N, SNC-RH124, SNC-RS44/46, SNC-RX, SNC-ER/EP and SNC-ZR/ZP series of PTZ cameras.
•
Vandal resistant, heavy duty construction, rated to IK10 standards.
•
Designed to be water and dust tight to IP66 standards.
•
Plenum rated for fire resistant ceiling applications.
•
Easy camera installation and servicing from below the ceiling or overhang.
•
Includes a decorative trim ring with safety lanyard and captive security fasteners.
•
Optically clear 0.118-inches (3mm) thick aspheric polycarbonate dome.
•
Thermostatically controlled 24VAC heater.
•
24VAC input with separate power inputs for heater, blower and camera power.
•
RoHS, WEEE, UL, CE compliant.
•
The outdoor dome camera housing shall be a Sony model UNI-OFL7C2 and UNI-OFL7T2. The housing shall be designed for the
SNC-RZ25N, SNC-RH124, SNC-RS44/46, SNC-RX, SNC-ER/EP and SNC-ZR/ZP series of PTZ cameras. These models shall also be
equipped with 24VAC input blowers and thermostatically controlled heaters. The back box shall be constructed from heavy
10-gauge aluminum and be capable of being installed in its entirety from below the ceiling. The top will measure (H x D) 6.75 x
9.16 inches. The lower dome shall be made of an injection molded, 3mm thick, optically clear thermoplastic polycarbonate (1
F-stop light reduction for tinted lower dome). The lower dome shall be held in place with a die-cast aluminum trim ring (white
powder coat finish) that attaches with a minimum of (3) security fasteners. The UNI-OFL7C2 and UNI-OFL7T2 shall be designed to
be installed in either sheetrock or hard ceiling surfaces. Three rotating support arms will allow for adjustment to the ceiling
material thickness. The unit shall be fully sealed, designed to meet IP66 dirt/water ingress rating. Unit will include thermostatically
controlled 25 watt heater and blower unit. The blower shall draw 1.4W continuous power. The 25W heater shall turn on at 40°F
(5°C) and turn off at 60°F (15°C). The housing shall support a temperature range of -20°F (-29°C) to 122°F (50°C).
equipped with 24VAC input blowers and thermostatically controlled heaters. The back box shall be constructed from heavy
10-gauge aluminum and be capable of being installed in its entirety from below the ceiling. The top will measure (H x D) 6.75 x
9.16 inches. The lower dome shall be made of an injection molded, 3mm thick, optically clear thermoplastic polycarbonate (1
F-stop light reduction for tinted lower dome). The lower dome shall be held in place with a die-cast aluminum trim ring (white
powder coat finish) that attaches with a minimum of (3) security fasteners. The UNI-OFL7C2 and UNI-OFL7T2 shall be designed to
be installed in either sheetrock or hard ceiling surfaces. Three rotating support arms will allow for adjustment to the ceiling
material thickness. The unit shall be fully sealed, designed to meet IP66 dirt/water ingress rating. Unit will include thermostatically
controlled 25 watt heater and blower unit. The blower shall draw 1.4W continuous power. The 25W heater shall turn on at 40°F
(5°C) and turn off at 60°F (15°C). The housing shall support a temperature range of -20°F (-29°C) to 122°F (50°C).
•
Note: To achieve the increased depth with the aspheric design for optimal camera lens to capsule orientation, the capsule is
slightly angled around the highest section. This creates a “line’, visible to the naked eye, around the upper most section of the
capsule. This “line” serves as the geometric center line used to insure proper camera placement. It is not typically seen by the
camera except when used with cameras that have above the horizon tilt capability.
capsule. This “line” serves as the geometric center line used to insure proper camera placement. It is not typically seen by the
camera except when used with cameras that have above the horizon tilt capability.
KEY FEATURES
BID SPECIFICATIONS
The UNI-OFL7C2 & UNI-OFL7T2 are a 7-inch recessed
dome enclosures that offer vandal resistance, versatility,
easy installation and camera protection in a compact
size. These inconspicuous, recessed dome housings are
specifically designed to accommodate the Sony
SNC-RZ25N, SNC-RH124, SNC-RS44/46, SNC-RX, SNC-ER/EP
and SNC-ZR/ZP series of PTZ cameras.
dome enclosures that offer vandal resistance, versatility,
easy installation and camera protection in a compact
size. These inconspicuous, recessed dome housings are
specifically designed to accommodate the Sony
SNC-RZ25N, SNC-RH124, SNC-RS44/46, SNC-RX, SNC-ER/EP
and SNC-ZR/ZP series of PTZ cameras.