Transition Networks SSDTF1029-123 SSDTF1029-123-NA Leaflet

Ordering Information 

  Twisted Pair (RJ-48) 

to  850nm multimode (ST) 

  Twisted Pair (RJ-48) 

to  850nm multimode (SC) 

  Twisted Pair (RJ-48) 

to  1300nm multimode (ST)

  Twisted Pair (RJ-48) 

  1310nm single mode (ST) 

  Twisted Pair (RJ-48) 

to  1310nm single mode (ST)

  Twisted Pair (RJ-48) 

to  1310nm single mode (SC)

  Twisted Pair (RJ-48) 

to  1310nm single mode (SC)

Twisted Pair (RJ-48) 

to  1310nm single mode (SC)

  Twisted Pair (RJ-48) 

to  1550nm single mode (SC)

  Twisted Pair (RJ-48) 

to  1310nm TX /1550nm RX single fiber SM 

(SC)

  Twisted Pair (RJ-48) 

to  1550nm TX/1310nm RX single fiber SM 

(SC)

  Twisted Pair (RJ-48) 

to  1310nm TX/1550nm RX single fiber SM 

(SC)

  Twisted Pair (RJ-48) 

to  1550nm TX/1310nm RX single fiber SM 

(SC)

Device

Device

Provide Campus Interconnects

Features

 

4

Remote unit in-band management  

     

4

Local or Remote Loopbacks on copper  

    or fiber in software mode 

4

Loopbacks via test set 

4

Converts the copper ports on T1/E1  

    devices, such as a PBX or T1/E1  

    Router, to multimode or single  

    mode fiber

4

Switch selectable RJ-48 connectors  

    for T1 or E1

4

Jitter attenuators optimize Bit Error  

    Rate (BER) performance

4

Network debug procedures make BER  

    testing more convenient

4

Built-in troubleshooting with the  

    addition of a selectable TAOS  

    (Transmit All Ones) switch on the fiber  

    and copper interfaces allows the  

    network engineer to test all T1/E1  

    equipment on that network segment  

    and ensure the network link

4

Dry Relay Contacts enable the device  

    to be tied into a separate alarm circuit  

    commonly found in a T1/E1 twisted  

    pair environment. Contacts will be  

    activated on loss of power or loss of  

    fiber link.

4

LED provides Alarm Indication  

    Signal (AIS)

4

Can be used with fractional  

    T1/E1 circuits

4

Report converter status
• Copper & Fiber Link status

• Hardware switch settings: LBO, AIS  

   Copper, AIS Fiber, HW/SW

• AIS detected Copper & Fiber

• Model Number

• Copper & Fiber Connector

4

Remote commands:

• Loopback Copper & Fiber 

• AIS transmitted on Fiber on loss of  

    Copper link

• AIS Transmitted on Copper on loss     

   of Fiber link

4

Extend PRI over fiber

see also: 

T1/E1 Point System™ Slide-In-Module NID 

4

Remote management in a stand-alone 

device  When  used  in  conjunction  with  a 
managed Point System™ chassis, this 
stand-alone unit can be managed remotely.

4

The Remotely Managed T1/E1 copper to 
fiber media converter will provide a solution 
for users who desire to extend their T1/E1 or 
PRI circuits over fiber and remotely manage 
them “in-band” from admin locations.

Specifications 

Standards 

ITU-T, ANSI, AT&T, ETSI

3-position Jumper 

Hardware: mode is determined by 4-position  

switch settings 

Software:  mode is determined by most recently 

saved on-board microprocessor settings.

Status LEDs 

PWR (Power): Steady green LED indicates  

connection to external AC power 

SDC (Signal Detect/Copper): On indicates twisted 

pair link is up 

SDF (Signal Detect/Fiber): On indicates fiber  

link is up

Dimensions 

Width: 3.25” [82 mm] 

Depth: 4.8” [122 mm] 

Height: 1.0” [25 mm]

Power 

External AC/DC provided; 12V DC; 0.5A; unregulated; 

standard;  

UL listed

Environment 

0 – 50°C, 

5% – 95% humidity (non-condensing),  

0 – 10,000 ft.

Shipping Weight 

2 lbs. [0.90 kg]

Safety Compliance 

Wall Mount Power Supply: 

CSA certified

Regulatory Compliance 

CISPR/EN55022 Class A;  

FCC Class A; CE Mark

Warranty 

Lifetime

Devices must be used in pairs. Typically installation will include a chassis card 
[CSDTF, pg 59] installed in the Point System™  locally and a stand-alone  
device installed at the remote location.

Optional Accessories (sold separately)

SPS-24602-PS 

    Piggy Back Power Supply

SPS-2460-SA  

    Stand-Alone Power Supply

    12-Slot Media Converter Rack

RMS19-SA4-01 

    4-Slot Media Converter Shelf

WMBD 

    DIN Rail Bracket 5.0” [127 mm]

WMBD-F  

    DIN Rail Bracket (flat) 3.3” [84 mm]

WMBL 

    Wall Mount Bracket 4.0” [102 mm]

WMBV 

    Vertical Wall Mount Bracket 5.0” [127 mm]