Tripp Lite UPSWM User Manual
Mounting Instructions
Collapsible
Wallmount Bracket
Model: UPSWM
Not suitable for mobile applications.
1111 W. 35th Street
Chicago, IL 60609 USA
Customer Support: (773) 869-1234
www.tripplite.com
W
A
RRANTY
REGISTRA
TION:
register online toda
y f
or a
chance to win a FREE
Tr
ipp Lite
product—www
.tr
ipplite
.com/w
arr
anty
Wallmount
Instructions:
Instructions:
The UPSWM is shipped in its
collapsible position and includes
two mounting braces. Open
the mounting bracket, hold the
bracket level against the intended
mounting surface and mark the
locations of the mounting holes
collapsible position and includes
two mounting braces. Open
the mounting bracket, hold the
bracket level against the intended
mounting surface and mark the
locations of the mounting holes
A
. Drill 1/8” guide holes in these
locations. Place the included
washers around the included
screws, then drive the screws
through the mounting holes and
into the guide holes. Install the
mounting braces by putting the
two buttons
washers around the included
screws, then drive the screws
through the mounting holes and
into the guide holes. Install the
mounting braces by putting the
two buttons
B
on each brace
through the holes on the side of
the unit
the unit
C
.
CAUTION: The hardware
(screws and washers) included
with the bracket is only intended
for use with plywood surfaces.
To mount your bracket on a
different surface, you must
determine a safe mounting
procedure and obtain proper
hardware.
(screws and washers) included
with the bracket is only intended
for use with plywood surfaces.
To mount your bracket on a
different surface, you must
determine a safe mounting
procedure and obtain proper
hardware.
Mounting a
UPS System or
Battery Pack:
UPS System or
Battery Pack:
CAUTION: Before mounting a
UPS, make sure the UPS is OFF
and unplugged. Before mounting
a BP36V27 battery pack, make
sure that the battery pack is
disconnected from your UPS
system. The UPS or battery pack
is extremely heavy. Take care to
avoid injury while lifting.
UPS, make sure the UPS is OFF
and unplugged. Before mounting
a BP36V27 battery pack, make
sure that the battery pack is
disconnected from your UPS
system. The UPS or battery pack
is extremely heavy. Take care to
avoid injury while lifting.
Place the UPS or battery pack
in the mounting tray. The feet of
a UPS should press against the
rear ridge
in the mounting tray. The feet of
a UPS should press against the
rear ridge
D
and fi t around the
center ridge
E
while the front of
the UPS presses against the front
ridge
ridge
F
. The base of a battery
pack should fi t between the rear
D
and center
E
ridges, with its
cords facing the wall.
Next, pass the safety strap
around the UPS or battery pack
and through the mounting tray as
shown. The safety strap should
pass through the tray’s outer
strap holes for a UPS or through
the tray’s inner strap holes for a
battery pack. Fully tighten the
safety strap and fasten the velcro
end.
around the UPS or battery pack
and through the mounting tray as
shown. The safety strap should
pass through the tray’s outer
strap holes for a UPS or through
the tray’s inner strap holes for a
battery pack. Fully tighten the
safety strap and fasten the velcro
end.
Mounting an
SNMP Solo (optional):
SNMP Solo (optional):
Affi x one of the self-adhesive
velcro pads included in the
bottom of the bracket’s SNMP
slot
velcro pads included in the
bottom of the bracket’s SNMP
slot
G
. Affi x the other pad to
the long side of the SMMP-Solo
opposite its indicator lights.
Press the velcro-covered side
of the SNMP-Solo into the
bracket’s SNMP slot.
opposite its indicator lights.
Press the velcro-covered side
of the SNMP-Solo into the
bracket’s SNMP slot.
Copyright © 2007. All rights reserved. The policy of Tripp Lite is one of continuous improvement. Specifi cations are subject to change without notice.
B
B
C
C
C
C
D
E
F
G
A
A
200706037 93-2696 UPSWM OM.indd 1
200706037 93-2696 UPSWM OM.indd 1
7/23/2007 3:34:53 PM
7/23/2007 3:34:53 PM