JVC LPT0484-001A User Manual
Masterpage:Right-NoTitle0
EN
53
Filename [HRJ880EU3.fm]
Page 53
May 18, 2001 2:45 pm
A
Make connections.
Connect the player’s VIDEO OUT and AUDIO OUT
connectors to your recorder’s VIDEO and AUDIO input
connectors on the front panel.
connectors to your recorder’s VIDEO and AUDIO input
connectors on the front panel.
B
Set the recorder’s input mode.
Press AUX (number key “0”) and/or PR to select “F-1”.
C
Locate the end point.
Load the recording cassette into your recorder, and play it
back to determine the edit-out point (the end of the
segment to be replaced) using the JOG dial, or pressing
back to determine the edit-out point (the end of the
segment to be replaced) using the JOG dial, or pressing
w
e
and
9
.
D
Reset the counter.
Press 0000.
● The counter is reset to “0:00:00”.
E
Locate the start point.
Determine the edit-in point (the beginning of the segment
to be replaced) using the JOG dial, or pressing
to be replaced) using the JOG dial, or pressing
w
e
and
9
.
● Be sure to engage the Still mode at the edit-in point.
F
Engage the Insert Editing mode.
Press INSERT.
● Your recorder enters the Insert Pause mode. (“
o
”, “
u
” and
“
i
” light up on the front display panel.)
● The TV screen changes from the still picture to the input
source you are going to record.
G
Start Editing.
Load the source cassette and play back the segment that
is to be inserted. When you reach the start of the section
of the source tape that you wish to insert, press
is to be inserted. When you reach the start of the section
of the source tape that you wish to insert, press
4
to start
the tape in your recorder; Insert Editing begins at this
point.
point.
● “
o
” and “
u
” are displayed on the front display panel.
H
End Insert Editing.
At counter “0:00:00”, Insert Editing will stop
automatically while the tape continues running in the
Play mode. If you wish to stop Insert Editing before the
specified edit-out point, press 0000.
automatically while the tape continues running in the
Play mode. If you wish to stop Insert Editing before the
specified edit-out point, press 0000.
AV Insert Editing
If you want to replace the picture, Hi-Fi audio soundtrack
and normal audio soundtrack all at the same time ...
... In step 6, after you press INSERT, press A.DUB also.
(
and normal audio soundtrack all at the same time ...
... In step 6, after you press INSERT, press A.DUB also.
(
“
o
” and “
u
” blink and “
i
” lights up on the front display
panel.)
NOTES:
● All necessary cables can be obtained from your dealer.
● Insert Editing is not possible with cassettes whose record safety
tab has been removed.
● When Insert Editing is performed on a tape that has been
recorded on another video recorder, the inserted portion may
appear distorted.
appear distorted.
● In Insert Editing, the recording speed (SP/LP) is determined by
the previous recording to be replaced. If the previous
recording’s speed changes within a single edit, the inserted
picture will be distorted at the switching point.
recording’s speed changes within a single edit, the inserted
picture will be distorted at the switching point.
● A small portion of the recording which precedes an insert edit
may become erased.
● Insert Editing is also possible using the rear panel AV1 (L-1) IN/
OUT or AV2 (L-2) IN/DECODER connector. When using these
21-pin SCART connectors, be sure to select the correct input
mode (“L-1” or “L-2”) in step 2.
21-pin SCART connectors, be sure to select the correct input
mode (“L-1” or “L-2”) in step 2.
HRJ880EU3.fm Page 53 Friday, May 18, 2001 2:54 PM