Gigaset AL110 Duo L36852-H2303-D201 User Manual

AL110/AL110A / UK / A31008-M2303-L101-1-7619 / main.fm / 07.06.2011

1)  Space

Nickel-metal-hydride (NiMH)

 

V30145-K1310-X383
(Valid at the time of going to press)
The handset is supplied with recommended 
batteries.

If you have any queries about the use of your tele-
phone, visit our website at 

 

www.gigaset.com/uk/service 

 

for 24-hour support. The table below contains a list of 
common problems and possible solutions.

1

1

£

$

¥

¤

2

a

b

c

2

ä

á

à

â

ã

ç

I

d

e

f

3

ë

é

è

ê

4

g

h 

i

4

ï

í

ì

î

5

j

k

l

5

L

m

n

o

6

ö

ñ

ó

ò

ô

õ

M

p

q

r

s

7

ß

N

t

u

v

8

ü

ú

ù

û

O

w

x

y

z

9

ÿ

ý

æ

ø

å

Q

.

,

?

!

0

+

-

:

¿

¡

"

’

;

_

P

  *

/

(

)

<

=

> %

#

 

Abc

--> 

123

123

-->

abc

#

@

\

&

§

AL110

AL110A

In standby mode
– Handset in base station

 

– Handset outside base station

ca. 1,0 W
ca. 0,8 W

ca. 1,2 W
ca. 1,0 W

During a call

ca. 1,0 W

ca. 1,2 W

DECT standard

is supported

GAP standard

is supported
(the Gigaset handset ope-
rates only with a Gigaset 
base)

Range

up to 300 m outdoors 

 

up to 50 m indoors

Base station power supply

230 V ~/50 Hz

Environmental conditions 
in operation

+5 °C to +45 °C, 20% to 
75% relative humidity

1)

Nothing 
appears in 
the display.

The handset is not 
switched on.

 

 

 

The batteries are 
flat.

Press the end call 
key 

a

 for approx. 

5 seconds or place the 
handset in the base 
station.
Charge or replace the 
batteries.

No wireless 
connection 
to the base sta-
tion, 
Base flashes in 
the display.

The handset is out-
side the range of 
the base station.
The handset is not 
registered.
The base station is 
not turned on.

Move the handset 
closer to the base 
station.

Register the handset 

¢

 p. 10.

Check the mains con-
nector on the base sta-
tion 

¢

 p. 3.

You cannot 
hear a ringer/
dialling tone 
from the fixed 
line network.

The phone cord 
supplied has not 
been used or has 
been replaced by a 
new cord with the 
wrong jack con-
nections.

Please always use the 
phone cord supplied or 
ensure that the 
pin connections are 
correct when purchas-
ing from a retailer: 

 

3-4 assignment of 
telephone leads/
EURO CTR37.

Error tone 
sounds after 

 

system PIN 
prompt.

PIN forgotten.

The system PIN you 
have entered is 
incorrect.

Reset the system PIN to 
the default 0000 

¢

 p. 11.