Datalogic CAB-532-KEU Leaflet

   

1. Power-off host.

2. Connect 8-pin mini-DIN on cable to 

POWERSCAN D8590. 

3. Connect 9-pin D-sub connector to 

host’s serial port.

4. Connect cable to power supply.

5. Plug in power supply and power-

on host.

6. Start a terminal program (such as 

Datalogic ESP’s Terminal or 

HyperTerminal) and set to 57.6K baud, 8 data bits, none 

parity, 2 stop bits.

7. Read the Reset to RS-232 Factory Defaults symbol, then 

the Save Settings symbol.

POWERSCAN D8590 DPM 

Imager, RS-232

PD8590-DPM

Kit, RS-232, 8’ coiled, US power 

supply

CAB-532-KUS

Kit, RS-232, 8’ coiled, EU power 

supply

CAB-532-KEU

Kit, RS-232, 8’ coiled, UK power 

supply

CAB-532-KUK

Note: The USB interface draws its power from the host.
Hardware for USB

1. Connect the USB cable to the host.
2. Open any program in your host 

computer that can receive keyboard 

text, such as Notepad. 

3. Read the Reset to USB Factory 

Defaults symbol below.            

Note: If you want symbol data to be 

entered as keyboard text, read the 

USB Keyboard Mode symbol 

below.

4. Read the Save Settings symbol below.

POWERSCAN D8590 DPM 

Imager, USB

PD8590-DPM

USB Cable

Included

1. One POWERSCAN D8590 Handheld DPM Imager
2. One 12 ft. USB cable (pre-attached to imager)

Parts List for RS-232 POWERSCAN D8590:
The RS-232 cable is affixed to the handle with two screws, a spacer, 

and a cable clip, which can be removed.

1. One POWERSCAN D8590 Handheld DPM Imager
2. Cable clip attachment
3. Spacer
4. Two threaded screws
5. RS-232 Interface Kit

• 8 ft. coiled RS-232 cable
• Power supply (U.S. Euro, or UK)

Datalogic and the Datalogic logo are registered trademarks of Datalogic
S.p.A. in many countries, including the U.S.A. and the E.U. PowerScan is a
registered trademark of Datalogic ADC, Inc. in many countries, including the
U.S.A. and the E.U. All other brand and product names may be trademarks
of their respective owners. 

Click on the ESP icon to run Datalogic ESP.

Note: Datalogic ESP can be installed from the Support Area at  

• 166 MHz Pentium processor (Pentium II processor recommended)
• Windows Vista, XP, or 2000 operating system
• Internet Explorer 5.0 or higher
• 64 MB minimum RAM (128+ MB RAM recommended)
• 80 MB hard drive space
• 800 x 600 minimum 256 color display (1024 x 768 32-bit color   

recommended)

Important: The imager must be in USB or RS-232 Mode to connect 

to ESP. Read the symbol below that corresponds with your communication 

interface, and then read the Save Settings symbol.

When you start ESP, the model menu will appear.

1. Click the POWERSCAN D8590 button and then click OK. 

If you do not want to make this selection every time you 

start ESP, uncheck “Show this dialog at startup”.

2. Select the default imager name (POWERSCAN D8590-1), 

or type a name of your choice in the Description text field and 

click OK.

3. Click Yes when this dialog appears:

820057290 (Rev A)

                May 2013