Panasonic PT-DZ680EK PT-DZ680ELKJ User Manual
Product codes
PT-DZ680ELKJ
S
P
E
C
F
I
L
E
PT-DZ680K/DZ680S/DZ680LK/DZ680LS
DLP
™
Projectors
As of October 2012
SFD12M014
1 3 / 1 7
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, com-
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
in this order. Add parameters according to the details of control.
Communication conditions (factory setting)
Pin assignments and signal names
6
1
5
9
D-sub 9-pin (female) Serial input
Description
NC
Send data
Receive data
Connected internally
Ground
Signal name
–
TXD
RXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
CTS
RTS
–
No.
6
7
8
9
Pin assignments and signal names
9
5
1
6
D-sub 9-pin (male) Serial output
Description
NC
Receive data
Send data
NC
Ground
Signal name
–
RXD
TXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
RTS
CTS
–
No.
6
7
8
9
CAUTION
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this
occurs, wait for 60 seconds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before
sending the next command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for com-
mand response to 10 seconds or more.
• When using two or more units:
1) Set different IDs for each unit.
2) Designate only one unit as RESPONSE (ID ALL) ON and the rest as RESPONSE (ID ALL) OFF.
3) Each group should have only one RESPONSE (ID GROUP) ON and the rest should be RESPONSE (ID GROUP) OFF.
2) Designate only one unit as RESPONSE (ID ALL) ON and the rest as RESPONSE (ID ALL) OFF.
3) Each group should have only one RESPONSE (ID GROUP) ON and the rest should be RESPONSE (ID GROUP) OFF.
Start
(1 byte)
(1 byte)
End
(1 byte)
(1 byte)
Colon
(1 byte)
(1 byte)
Semicolon
(1 byte)
(1 byte)
(2 byte)
ID designator
01 to 64: Address number
0A to 0Z: Group ID
ZZ: All units (ID ALL)
0A to 0Z: Group ID
ZZ: All units (ID ALL)
ID: 2 characters
(2 bytes)
Parameters
(undefined length)
(undefined length)
Command
(3 bytes)
(Control and/or query commands)
(3 bytes)
(Control and/or query commands)
STX
ETX
C1
P1 P2 ... Pn
C2
A
D
I1 I2
C3
:
;
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
9,600 bps
None
8 bits
1 bit
None
None