Panasonic PT-DZ10KE User Manual
As of April 2013
SFD12M023
1 6 / 1 7
S
P
E
C
F
I
L
E
PT-DZ10K
3-Chip DLP
™
Projector
500 mm (19-11/16˝ ) or more
500 mm (19-11/16˝ )
or more
or more
500 mm (19-11/16˝ )
or more
or more
Do not stack pr
Do not support
the projector unit
by its top while
it is in use.
the projector unit
by its top while
it is in use.
ojector
units directly on top of
one another.
one another.
100 mm
( 3 -15 / 16 in)
or more
( 3 -15 / 16 in)
or more
Notes on projector placement and operation
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
following precautions.
1. Never place objects on top of the projector while it is operating.
2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s
exhaust openings.
3. Do not stack projector units directly on top of one another. If two units must be stacked for backup
use in ordinary projection, use a method as shown below and provide ample space between the
units to ensure that exhaust heat does not accumulate near the intake opening or around the units.
Dual stacked projection is not recommended.
units to ensure that exhaust heat does not accumulate near the intake opening or around the units.
Dual stacked projection is not recommended.
4. Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the projector
so that cool or hot air from other air conditioning equipment does not flow directly toward the
projector’s air intake or exhaust openings.
projector’s air intake or exhaust openings.
5. Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed
space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the
intake opening. This may cause the projector’s protective circuit to interrupt projector operation.
intake opening. This may cause the projector’s protective circuit to interrupt projector operation.
6. If the projector is installed in an enclosed space, ensure that the temperature of the air surrounding
the projector is between 0 °C and 45 °C (32 °F and 104 °F). Also make sure that the projector’s intake
and exhaust openings are not blocked. Even though the air surrounding the projector is 40 °C
(104 °F) or less, if hot exhaust air accumulates inside the space, it may cause the projector’s protective
circuit to interrupt projector operation. Pay particular attention to the surrounding temperature
conditions when planning the installation.
and exhaust openings are not blocked. Even though the air surrounding the projector is 40 °C
(104 °F) or less, if hot exhaust air accumulates inside the space, it may cause the projector’s protective
circuit to interrupt projector operation. Pay particular attention to the surrounding temperature
conditions when planning the installation.
7. If the projector is not to be set on the floor using adjuster legs, install it by using the five ceilingmount
screw holes (screw diameter: M6, length of each screw hole in the projector: 16 mm (5/8˝)).
Provide a space of 5 to 10 mm (3/16˝ to 13/32˝) between the projector and the mounting surface by
inserting metal spacers.
Provide a space of 5 to 10 mm (3/16˝ to 13/32˝) between the projector and the mounting surface by
inserting metal spacers.
SHUTTER
SHUTTER
LENS
LENS
ENTER
ENTER
AUTO
AUTO
MENU
MENU
SETUP
SETUP
VIDEO
VIDEO
S-VIDEO
S-VIDEO
RGB1
RGB1
RGB2
RGB2
DVI-D/HDMI
DVI-D/HDMI
SDI
SDI
SHUTTER
SHUTTER
LENS
LENS
ENTER
ENTER
AUTO
AUTO
MENU
MENU
SETUP
SETUP
VIDEO
VIDEO
S-VIDEO
S-VIDEO
RGB1
RGB1
RGB2
RGB2
DVI-D/HDMI
DVI-D/HDMI
SDI
SDI
SHUTTER
SHUTTER
LENS
LENS
ENTER
ENTER
AUTO
AUTO
MENU
MENU
SETUP
SETUP
VIDEO
VIDEO
S-VIDEO
S-VIDEO
RGB1
RGB1
RGB2
RGB2
DVI-D/HDMI
DVI-D/HDMI
SDI
SDI
SHUTTER
SHUTTER
LENS
LENS
ENTER
ENTER
AUTO
AUTO
MENU
MENU
SETUP
SETUP
VIDEO
VIDEO
S-VIDEO
S-VIDEO
RGB1
RGB1
RGB2
RGB2
DVI-D/HDMI
DVI-D/HDMI
SDI
SDI