Gigaset S800 S30852-H2106-D201 User Manual
Product codes
S30852-H2106-D201
79
Gigaset S800-S800A / en Großbritannien / A31008-M2125-L101-1-7619 / appendix.fm / 20.05.2010
V
e
rsion 4.1, 21
.11.2007
Questions and answers
If you have any questions about the use of
your phone, you can contact us 24/7 at
www.gigaset.com/customercare.
your phone, you can contact us 24/7 at
www.gigaset.com/customercare.
The table below contains a list of common
problems and possible solutions.
problems and possible solutions.
Gigaset S800A only:
Anmelde- oder Verbindungsprobleme mit
einem Bluetooth Headset.
einem Bluetooth Headset.
¥
Reset am Bluetooth Headset durchführen
(siehe Bedienungsanleitung Ihres Headsets).
(siehe Bedienungsanleitung Ihres Headsets).
¥
Anmeldedaten im Mobilteil löschen, indem
Sie das Gerät abmelden (
Sie das Gerät abmelden (
The display is blank.
1. The handset is not switched on.
¥
Press and hold the end call key
a.
2. The battery is empty.
Not all menu items are displayed.
The menu display is restricted (standard mode).
¥
Activate extended menu display
(expert mode
(expert mode
•
No Base
flashes on the display.
1. The handset is outside the range of the base.
¥
Move the handset closer to the base.
2. The base's range is reduced because
Eco Mode is activated.
¥
Deactivate Eco Mode (
reduce the distance between the handset
and the base.
and the base.
3. The base is not switched on.
Please register handset
flashes on the display.
Handset has not been registered with the base or
has been deregistered.
has been deregistered.
¥
Register the handset (
Handset does not ring.
1. The ringtone is deactivated.
¥
Activate the ringtone (
¥
Deactivate call divert (
3. The phone only rings if the phone number
has been transferred.
You cannot hear a ringtone/dialling tone from
the fixed line network.
the fixed line network.
The phone cord supplied has not been used or
has been replaced by a new cord with the wrong
pin connections.
has been replaced by a new cord with the wrong
pin connections.
¥
Please always use the phone cord supplied or
ensure that the pin connections are correct
when purchasing from a retailer
(
ensure that the pin connections are correct
when purchasing from a retailer
(
Error tone sounds after system PIN prompt.
You have entered the wrong system PIN.
¥
Reset the system PIN to 0000 (
Forgotten the system PIN.
¥
Reset the system PIN to 0000 (
The other party cannot hear you.
You have pressed the mute button
h. The
handset is "muted".
¥
Reactivate the microphone (
The number of the caller is not displayed
despite CLIP.
despite CLIP.
Calling Line Identification is not enabled.
¥
The caller should ask the network provider to
enable Calling Line Identification (CLI).
enable Calling Line Identification (CLI).
You hear an error tone when keying an input (a
descending tone sequence).
descending tone sequence).
Action has failed/invalid input.
¥
Repeat the operation.
Watch the display and refer to the user guide
if necessary.
Watch the display and refer to the user guide
if necessary.
You cannot listen to messages on the network
mailbox.
mailbox.
Your PABX is set for pulse dialling.
¥
Set your PABX to tone dialling.
No time is specified for a message in the call list.
Date and time have not been set.
¥
Set the date and time (