Makita 9558HN User Manual
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model 9556HN
9557HN
9558HN
Depressed center wheel diameter
100 mm
115 mm
125 mm
Spindle thread
M10
M14
M14
Rated speed (n) / No load speed (n
o
) 11000
min
-1
11000
min
-1
11000
min
-1
Overall length
271 mm
271 mm
271 mm
Net weight
1.9 kg
2.0 kg
2.1 kg
Safety class
/II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END202-6
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Be sure that you understand their meaning before use.
･ Read instruction manual.
･ DOUBLE
･ DOUBLE
INSULATION
･ Wear
safety
glasses.
･ Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.
ENE048-1
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
For Model 9557HN
ENG102-3
Noise
The typical A-weighted noise level determined according
to EN60745:
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
pA
) : 86 dB(A)
Sound power level (L
WA
) : 97 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
ENG208-5
Vibration
The vibration total value (tri-axial vector sum)
determined according to EN60745:
The vibration total value (tri-axial vector sum)
determined according to EN60745:
Work mode : surface grinding
Vibration emission (a
Vibration emission (a
h,AG
) : 7.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
The declared vibration emission value may also be used
in a preliminary assessment of exposure.
The declared vibration emission value is used for main
applications of the power tool. However if the power tool
is used for other applications, the vibration emission
value may be different.
measured in accordance with the standard test method
and may be used for comparing one tool with another.
The declared vibration emission value may also be used
in a preliminary assessment of exposure.
The declared vibration emission value is used for main
applications of the power tool. However if the power tool
is used for other applications, the vibration emission
value may be different.
WARNING:
•
The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
•
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).