Yongnuo YN-468 II BINGSALE Leaflet

Product codes

BINGSALE

6. S1/S2 Mode

Press the [MODE] button, then the flash will enter S1/S2 mode.

These modes are applicable for slave flash in order to create many

light effects. They are respectively applicable for manual flash

environment and TLT flash environment.

When the flash is in S1 mode, it will work with the first work of

the master flash synchronously, with the result consistent with the

use of radio slave. To use this mode correctly, the master flash

should be set at manual flash and the TTL flash system with

preflight function and the red-reduction function with multiple

flashes should not be used.

S2 mode is similar to S1 mode, but it can support the master flash

in TTL mode. In particular, if S1 mode cannot have correct and

synchronous flash with the inbuilt flash, you can try to use S2

mode.

7. Menu Access of Camera (only compatible with Canon

ETTL camera system)

On the Canon camera

supporting ETTL, you can

switch flash mode via the

camera menu. With the

setting function of the

external flash function in the

flash control menu, you can

switch between the TTL

mode and the manual flash mode; in addition, on such menu, you

may also set front and rear curtain synchronization, and set

manual flash output with 1/3ev step length.

8. Test Flash

Whether in any mode, you can press PILOT button to test if the

flash light flashes normally.

In M/S1/S2 mode, press the PILOT button and the flash light will

send light with different luminance as per levels of output power

selected.

9. Power-saving Function

In TTL/M/MULTI mode, if idle for about 30min, the flash will

power off automatically.

In S1/S2 mode, if idle for 60min, the flash will power off

automatically.

VI. Specifications

Guide number                          33
Circuit design                          Insulated Gate Bipolar Transistor (IGBT)
Flash mode                              TTL, M, Multi, S1, S2
Zoom range

Auto, 24, 28, 35, 50, 70, 85 mm

Vertical rotation angle              -7~90 degrees
Horizontal rotation angle          0~270 degrees
Power Supply                          4×AAsize batteries (Alkaline or Ni-MH

are usable)

Lighting times                        100~1500 times (AA alkaline cell used)
Recycle time                           less than 3s (AA alkaline cell used)
Color temperature                    5600k
Flash time                                1/800s~1/20000s
Flash control                            TTL auto flash or manual Level 8 light

quantity output control with 0.3 stop
increment

Additional features FEB, FEC, FEL, Automatic zooming,

Rear-curtain Sync.

Dimensions                              60×72×172 mm(extended state)
Net weight                                300g
Accessories                              Flash light (1), protecting bag (1), and

mini stand(1) and manual (1)

VII. Possible problems during use and solutions

1. The AF LED is not on? Check if this camera needs flash light

assist AF or if it supports the function; some cameras requires

focucal points to be in the center, focus method to adopt AF-S and

requires dark environment; check if some settings in the camera

are forbidden.

2. Photos are under exposure or over exposure? Check if the set

shutter, aperture and ISO are too near the flash limit or if some

settings including exposure compensation in relation to flash are

proper.

3. Vignetting appears in photos or only part of the subject is

illuminated? This product has a designed light head zoom range

of 24-85 mm, and is currently not compatible with full frame

camera system. You may pull out the wide-angle diffuser to widen

the flash range.

4. Because of differences among various models of cameras and

different personal preferences, the use of this product may cause

brightness with the [Output control knob] within the range of ±3ev,

with the precision of 1/3ev. Please Note that this compensation

setting will override the exposure compensation setting on the

camera.

8. Reflection Flash

Bounce flash means to take photos by making flash light head

aimed at wall or ceiling and using the light reflected back from the

ceiling or wall to light the desired object, so that the shade behind

the object can be decreased to get

more natural shooting effect.

If the wall or ceiling is too far, the

bounce flash may be too weak to

get enough exposure. The wall or

ceiling should be even and white

in order to get efficient reflection;

if the reflection surface is not

white, color cast may appear in photo.

9. Use Reflection Board to Take Photos

With the reflection board flash, draw the reflection board and the

wide-angle diffusion board out from the light head at the same

time and then push the wide-angle

diffusion board back. In such case,

if this product is being used to take

photos, it will produce a

highlighted point on the eyes of

the subject and thus make the eyes

charming (catch light). This

function can reach optimal effect

when the flasher head is up 90°.

10. Use Wide-angle Diffuser

Pull out the wide-angle diffusion board,

push back the reflection board and

arrange them as per the figure; in such

case, the flash scopes will extent to 18

mm and the flash effect will be softer and

more natural.

Note: When this product is used in incompatible iTTL/ETTL

camera, Functions 2, 3, 4, 5, 6 and 7 are not available.

after 3 photos are taken, exposure compensation will be made

automatically in the sequence of, for example, “normal under

over”. This function helps you improve the success rate of

photo taking.

3. FV Lock (Nikon)

Set the AE-L/AF-L function as FV Lock on the camera before

using this function. At this time, you can aim at your desired

object in the viewfinder and then press the AE-L key or AF-L key,

in such case, the flash light will pre-flash to get the reading of

flash exposure for the object; after you have confirmed the scene

frame, press the shutter. (This function can only be available when

your camera supports it; for the setting of AE-L and AF-L, refer to

your camera manual)

4. FE Lock (Canon)

To use this function, cover the subject for which flash exposure

will be locked at the center of the viewfinder of camera, press the

button <*> of the flash exposure lock, and the flash light will

pre-flash and the camera will calculate the appropriate flash

output data. Now you have some time for recomposition, after

which, you can take photo. (The function can be used only when it

is supported by your camera. For the setting method, refer to your

Camera Instructions.)

5. Rear-curtain Sync

You can use slow-speed shutter to produce trailing smear for the

object and the flash light will flash at the moment when the shutter

is going to be shut, which means the rear-curtain sync

function .(For the rear-curtain sync setting, refer to your camera

manual for setting)

6. Application of AF LED

If the object or environment lacks sufficient light, the camera can

not conduct accurate focusing; at this time, the flash light can give

out AF light to assist in the camera’s focusing so as to achieve

accurate focusing.

7. Exposure Compensation

You can use the exposure compensation function of this camera to

compensate flash output so as to make shooting effect better meet

your requirements. （ For Canon version, the exposure

compensation function on camera is available only in TTL mode)

In the TTL mode, you can also make compensation of flash

一、警告：

请勿让本产品淋雨或受潮，以免发生火灾或触电。

处理电池时，请将电池的触点包裹好以避免短路，并请遵守好当

地有关处理电池的规定。

请将电池或容易误吞的东西远离儿童存放，如果误吞了物体，请

立即与医生联系。

不要近距离对人体的眼睛使用闪光元件，否则有可能对人体视网

膜造成伤害。

不要对需要高度注意力的人使用闪光灯，否则有可能引发安全事

故。

如果发生以下情况，请立即取出电池并停止使用：

本产品跌落或受到强烈冲击，使产品的内部裸露。

电池内部腐蚀性液体泄漏，此时应带手套取出电池。

产品发出奇怪的气味，发热或冒烟。

请勿自行拆卸或维修本产品，如果接触产品内部的高压电路，可

能会触电。

长期不使用本产品时，请取出所有电池。

二、部件及显示屏说明

1、反射板
2、广角扩散板
3、闪光灯头
4、电池仓盖
5、辅助对焦灯及

无线触发感应器

6、固定旋钮
7、热靴座
8、热靴触点

物对焦后按下相机快门，闪光灯就会根据相机的指示闪出合适的

光，就可以得到您所需要的相片。

在

TTL 模式下，您还可以通过【＋】与【－】按钮对闪光亮度进

行补偿，补偿范围是±

3ev，精度为 1/3ev。

注意：该补偿值将覆盖相机上的闪光补偿设置。

4、M 模式
该

M 模式下，您可以根据自己的喜好设定闪光亮度，通过【＋】

与【－】按钮可以调节闪光亮度。

闪光亮度的调整范围是

1/128~1/1，

调整步长为

0.3。拍摄时, 您只需要设定闪光亮度，调整相机并按

下快门，闪光灯会在相机同步信号下进行闪光。

5、Multi 模式
MULTI 模式即频闪模式，在该模式下，闪光灯将按您设置的输出
功率、闪光次数与频率闪光。通过【＋】与【－】可以调整输出

功率，输出功率的调整范围是

1/128-1/64-1/32-1/16-1/8-1/4。要调

整闪光次数与闪光频率，请先按一次【＋】，输出功率将闪烁，在

此状态下按【模式切换按钮】即

MODE 按钮，闪光次数将闪烁，

此时按【＋】与【－】可以调整闪光次数，再按【模式切换按钮】，

闪光频率将开始闪烁，此时按【＋】与【－】可以调整闪光次数。

注意：电池电量不足的情况，闪光灯充电速度较慢，可能会引起

高频率闪光出现漏闪，在这种情况下，请降低闪光频率或更换新

电池。

6、S1/S2 模式
通过按下【模式切换按钮】，可以使闪光灯进入

S1、S2 模式。这

两种模式适合作为离机副灯使用，以创建多种照明效果，它们分

别适合于手动闪光环境和

TTL 闪光环境。在这两种模式下调整输

出亮度和

M 模式一样，只需要按【＋】与【－】就可以了。

S1 模式：当闪光灯处于 S1 模式，它会与主闪光灯的第一次闪光
同步触发闪光，效果与使用无线引闪器一致。要正常使用该模式，

您的主闪光灯应设置为手动闪光，不应使用具有预闪的

TTL 闪光

系统，也不应使用具有多次闪光的红眼减轻功能。
S2 模式：又被称为“预闪取消模式”，该模式与 S1 模式类似，但
它能支持工作在

TTL 模式的主闪光灯。特别地，如果 S1 模式无

法与您的内置闪光灯正确同步闪光，您可以尝试使用

S2 模式。

用时有效），方法是：先按住【模式切换按钮】不释放，再按【＋】

。

每按一次，闪光灯将在前帘同步和后帘同步之间切换。

6、使用【辅助对焦灯】

不足的情况下，由于相机不能准确的

闪光灯上关闭对焦灯，方法是：先按住【模式切换按钮】

、曝光补偿

曝光补偿：您可以使用相机的闪光曝光补偿功能

钮对闪光亮度进

。

、反射闪光

过将【闪光灯头】指向

可能

、利用【反射板】拍摄

反射板】

在拍摄主体或环境处于光线

对焦，此时闪光灯能发出对焦光帮助相机对焦。从而完成准确的

对焦。

您可以在

不释放，再按【－】

。每按一次，对焦灯开关将打开或关闭。需要

注意的是，只有相机和闪光灯上的辅助对焦均开启的情况下，闪

光灯才能发出辅助对焦光线。

7
相机上设置闪光

来调整闪光输出量，使拍摄效果更符合您的需求（对于佳能相机，

在相机上的闪光曝光补偿仅在

TTL 模式可用）。

在

TTL 模式下，您还可以通过【＋】与【－】按

行补偿。补偿范围是±

3ev，精度为 1/3ev。

注意：该补偿值将覆盖相机上的闪光补偿设置

8
反射闪光是指通

墙壁或天花板，借助天花板或墙壁反射

回来的光照亮物体来进行拍摄（俗称

“跳闪”）

。这样可以减轻被摄物体背后

阴影，获得更自然的摄影效果。

如果墙壁或天花板太远，反射闪光

太弱导致曝光不足。墙壁或天花板应该

于高效的反射，如果反射表面不是白色的，照片上可能会出现偏

色。

是平坦的，白色的，以利

9
使用【反射板】闪光，把【

和【广角扩散板】从灯头一起拉出，

将【广角扩散板】推回。如果此时

进行拍摄，可以在主体的眼睛造成

高光点，使眼神更加迷人有光彩（眼

七

使用过程中可能出现的问题和解决方法

、对焦灯不亮？请确认闪光灯上的对焦开关是否打开；确认该相

、照片欠曝或过曝？检查此时照相机设置的快门，光圈，感光度

、相片出现暗角或者被摄物体只有局部能照亮？本产品设计的灯

、由于各型号相机的差异以及个人喜好关系，使用本产品有可能

、如果您觉得闪光灯控制面板模糊，这是因为面板贴有一层保护

、闪光灯状态异常？请试图关闭闪光灯与相机的电源，在相机热

、户外使用柔光伞注意：当在户外闪光灯安装柔光伞的时候容易

、

S1、S2 离机引闪不成功？使用 S1、S2 模式时请避免以下情况：

1
机是否需要闪光灯辅助对焦或者该相机是否支持该功能，某些相

机需要对焦点在中央，对焦方式为单次对焦（

AF-S），并且需在较

暗环境。请确认是否相机上的设置被禁用。

2
（

ISO）是否过于接近闪光的极限，或者相机曝光补偿、曝光包围

等与闪光有关的设置是否正确。

3
头变焦范围是

24~85mm，并且目前不兼容全画幅相机系统，您可

以尝试拉出广角扩散板，以扩大闪光范围。

4
出现整体过曝或欠曝的情形，请试图通过相机闪光补偿或曝光补

偿设置进行调整。

5
膜，您可以撕开它来享受更清晰的视觉效果。

6
靴上安装好闪光灯后，再重新打开闪光灯与相机电源。如仍有异

常，请更换一组新电池再尝试使用。

7
被风吹倒，导致闪光灯热靴脚摔断，请固定安装架或避免户外使

用。

8
在户外被阳光直接照射无线触发感应器；主灯使用红眼减轻功能；

主灯使用指令模式（尼康）或无线模式（佳能）

；使用

ST-E2 作为

闪光控制器。

、

9、LCD 显示屏
10、[＋]、[-]按钮
11

、测试按钮（

PILOT）

12、模式切换按钮（MODE）
13、PC接口

、电源按钮（

ON/OFF）

14、充电指示灯

LCD 面板说明

16、模式指示
17、功率/EV 指示
18

、

ISO 指示（尼康版本）

、光圈指示

、输出功率微调

/频闪频率指示

、频闪次数指示

、后帘同步指示

、对焦灯开关指示

、灯头焦距指示

、灯头手动变焦指示

三、产品安装

1、安装电池。
按箭头所示方向滑动【电池仓盖】将其打开。

按电池仓中贴纸的指示安放电池，确保电池的正

负极接点朝向正确。

按箭头所示方向滑动【电池仓盖】将其关闭。

注意：请使用

4 颗标准规格的 AA 电池。请勿使

用外皮破损的电池，防止发生短路。

2、将闪光灯安装到相机上。
按箭头所示方向转动【固定旋钮】到最高点。

将闪光灯【热靴座】完全推入相机热靴。

如箭头所示方向转动【固定旋钮】拧紧。

要取下闪光灯，请松开【固定旋钮】，然后从相机热靴中推出。

四、基本功能

1、基本操作
按钮的操作：

部件

操作

【电源开关】

闪光灯电源开关。长按该按钮

2 秒可打开

或关闭闪光灯电源。推荐通过该按钮关闭

闪光灯电源之后再取出电池。

【模式切换按钮】

每按一次，闪光灯模式依次在
TTL/M/Multi/S1/S2 之间循环切换。

【测试按钮】

按下测试闪光输出亮度。

【＋】与【－】按钮

在

TTL 模式下，通过该按钮可以调整曝

光补偿（将覆盖相机的闪光补偿）。

在

M、MULTI、S1、S2 模式下，通过该

按钮可以调整闪光灯输出功率。

在

MULTI 模式下，该按钮还用于调整频

闪次数与频率，请参阅

MULTI 模式一节。

【模式切换按钮】

【－】

请先按住【模式切换按钮】不释放，再按

【－】。每按一次，对焦灯开关将打开或

关闭。

【模式切换按钮】+

【＋】

请先按住【模式切换按钮】不释放，再按

【＋】。每按一次，闪光灯将在前帘同步

和后帘同步之间切换。

【模式切换按钮】

【电源按钮】

请先按住【模式切换按钮】不释放，再按

【电源按钮】。每按一次，闪光灯灯头焦

距将在（

auto / 24 / 28 / 35 / 50 / 70 / 85mm）

之间循环切换

【充电指示灯】状态含义

【充电指示灯】

状态

含义

处理方法

亮红灯

闪光灯充电完成，可

进行闪光

正常

亮绿灯

闪光灯充电未完成

如长时间亮绿灯，请

更换新电池

绿灯闪烁

因电池电量不足，闪

光灯被锁定

请更换新电池

红绿交替闪烁

因频繁闪光，防止过

热，闪光灯被锁定

静置大约

3 分钟，等

待闪光灯冷却

2、开启及关闭电源
长按【电源开关】

2 秒可打开或关闭闪光灯电源。推荐通过该按钮

关闭闪光灯电源之后再取出电池。

打开闪光灯电源后，闪光灯被设定为

TTL 模式，或保留上次关机

前状态。此时【充电指示灯】亮起绿灯，数秒后充电完毕会转亮

红灯，表示可以进行闪光。

若【充电指示灯】一直亮绿灯，充电时间超过

20 秒仍充不满，闪

光灯将自动关机。此时需要更换新电池。

使用完毕后，长按【电源开关】

2 秒即可关闭电源。

3、TTL 模式
在

TTL 模式下，照相机的测光系统会侦查从主体反射回来的闪光

照明，从而自动的控制闪光的输出量。拍摄时，您只需要对准景

13、PC 同步接口(输入)
通过连接PC接口，可以使闪光灯同步闪光。

7、相机菜单访问功能（佳能）
在支持

ETTL 的佳能相机上可以通

过相机菜单来切换闪光灯模式。在

闪光灯控制菜单内的外接闪光灯功

能设置功能，可以切换

TTL 模式、

手动闪光模式及多次闪光模式（频

闪），而且在此菜单可以设置前帘、

后帘同步，曝光包围，以

1/3ev 为步长设置手动闪光输出，以及频

闪的次数与频率。

8、测试闪光
无论处在哪种模式下，您都可以通过按

PILOT 按钮来测试闪光灯

是否闪光正常。

M/MULTI/S1/S2 模式下，按【测试按钮】，闪光灯

会根据所选择的输出功率的等级发出不同亮度光。

9、节电功能
在

TTL/M/Multi 模式下，闲置30分钟后闪光灯将自动关机。

在

S1、S2 模式下，闲置 60 分钟后闪光灯将自动关机。

10、过热保护
连续拍摄过于频繁时，将触发闪光灯的过热保护机制，此时充电

指示灯将红绿交替闪烁，且锁定闪光灯。请将闪光灯静置 3～5 分

钟，等待保护状态解除后继续拍摄。为避免影响拍摄，需要快速

拍摄时，请尽量使用

1/4 及以下输出。

11、灯头自动变焦
当闪光灯安装在支持

i-TTL/ETTL 的相机系统时，闪光灯管将会随

着镜头焦距变化而前后移动，以适应不同的照明范围。注意：灯

头自动变焦不支持全幅面相机系统，但可以尝试将广角扩散板拉

出以避免照片出现暗角。

12、手动设置灯头变焦位置
通过按【模式切换按钮】

+【电源按钮】可以手动设置灯头的变焦

位置。请先按住【模式切换按钮】不释放，再按【电源按钮】

。每

按一次，闪光灯灯头焦距将在（

auto / 24 / 28 / 35 / 50 / 70 / 85mm）

之间循环切换。

五、高级应用

1、多灯布光应用
使用内置闪光灯或机顶外置闪光灯作为主灯。

将闪光灯作各种不同的方向摆放。

在室内使用时，无线信号可通过

墙壁反射回来，因此，在放置副

闪光灯时可以有更多空间。

放置副闪光灯时，请在拍摄前先

测试

S1 或S2 模式是否正常同步。

请勿在主闪光灯及副闪光灯之间放置障碍物，障碍物会阻碍无线

、曝光包围（

FEB）

上进行设置，设置方法请参照您的相机

、

FV 锁定（尼康）

将（

AE-L/AF-L）功能设置为“FV 锁定”。

、

FE 锁定（佳能）

景器中央覆盖要锁定闪光曝光的主体，

、后帘同步

快门，为拍摄主体制造拖影，闪光灯会在快门即

置后帘同步（但只在相机上使

信号的传送。

2
曝光包围功能需要从相机

说明书。设置了曝光包围后，每拍摄

3 张照片将自动对曝光进行

一定正负补偿，例如按照“正常不足过度”的顺序进行曝光，

这个功能可以帮助您提高拍摄的成功率。

3
使用本功能应先在相机上

此时可以先在观景窗中对准主体，然后按下相机的（

AE-L/AF-L）

键，闪光灯会先发出预闪为主体取得闪光曝光的读数，当您确定

拍摄的景物框架后按下快门即可。

（此功能需要您的相机支持该功

能才能使用，

（

AE-L/AF-L）的设定请参照您的相机说明书进行。

4
使用本功能应先将相机取

按下闪光曝光锁

<*>按钮，闪光灯发出预闪，相机将计算适合的闪

光输出数据，此时你有一段时间来重新构图，构图完毕后就可以

按下快门拍摄照片（该功能需要您的相机支持该功能才能使用，

请参照您的相机说明书进行设置）。

5
您可以使用慢速

将关闭的那一刻闪光。这就是后帘同步功能（后帘同步的设定请

参照您的相机说明书进行设置）

。

对于佳能版本，可以在闪光灯上设

神光）

。此功能在闪光灯头上仰

90 度时能达到最好的效果。

10、使用【广角扩散板

意：在不相容

i-TTL/ETTL

、

4、

、规格

绝缘两级晶体（

IGBT）

性电池或

AA 镍氢（Ni-MH）电池

/20000s

级手动光量输出控制

附加功能

自动变焦、后帘同

体积

（伸展状态）

（

1），保护袋（1），微型底座（1），

拉出【广角扩散板】推回【反

射板】，并按图示意摆放，闪

光范围将会扩大，同时闪光效

果将更加柔和自然。

注

相机上使用本产品时，以上

2、3

5、6、7 功能均不能使用。

六

闪光指数

线路设计

自动

闪光模式

TTL、M、Multi、S1、S2

灯头变焦范围

Auto、24、28、35、50、70、85 mm

上下旋转角度

-7~90 度

左右旋转角度

0~270 度

电源

4 枚 AA 碱

发光次数

100~1500 次（使用 AA 碱性电池）

回电时间

小于3秒（使用 AA 碱性电池）

色温

5600k

闪光灯时间

1/800s~1

闪光控制

TTL 自动闪光或 8

(1/128~1/1), 精度为 0.3 级
曝光包围、曝光补偿、灯头

步、曝光锁定
60×72×172 mm

净重

250g

所含物品

闪光灯

说明书（

1）

本使用说明书中的功能是依据本公司的测试条件获得的。设计和

徽标是深圳永诺摄影器材股份

二栋西

A511 室

规格如有变更，恕不另行通知。

本说明书中的永诺（

YONGNUO）

有限公司在中国或

/和其他国家（地区）的注册商标或商标。其他

所有商标均为其各自所有者拥有。

地址：深圳市华强北路赛格科技园
网址：

www.hkyongnuo.com

深圳市永诺摄影器材股份有限公司

全国服务热线：400-001-3888

I. Caution

To avoid fire or electrical shock, do not expose this product to rain

or moisture.

Do not flash at high level output continuously for over 15 times.

To avoid short circuit, be sure the batteries contacts are securely

packed and in accordance with local provision when handling the

batteries.

Please place the batteries and the parts which can be swallowed

mistakenly away from children. Contact a doctor immediately

when it occurs.

To avoid possible injury to eyes, do not use the flush light in a

short distance from the eyes.

To avoid possible safety accident, do not use the flush light on the

people who need a high degree of attention.

Please take out the batteries and stop using immediately in case of

below:

●

This product is dropped or shocked seriously and the inner part

of the product is bared.

●

If the battery leaks corrosive liquids, please take out the battery

with gloves.

●

The product gives off strange smell, smokes or heats.

Do not disassemble or maintain this product. Touching the

internal high voltage circuit will cause electric shock.

II. Nomenclature

1. Reflection board

2. Wide-angle diffuser

3. Flash light’s head

4. Battery chamber’s cover

5. AF LED and optical

control sensor

6. Locking ring

7. Hot shoe stand

8. Hot shoe pin

9. LCD panel

10. +/- buttons

11.

Test button

12. Mode switch button

13.

Power switch

14. Charging indicator
15.

LCD panel description

16. Mode indicator

17. Output/EV indicator

18.

ISO indicator (for Nikon version)

19.

Aperture indicator

20.

Output level fine / frequency indicator

21.

Flash times indicator for Multi mode

22.

Read-curtain indicator

23.

AF LED switch indicator

24.

Flash head zooming indicator

25.

Flash head manual zoom indicator

III. Installation Instruction

1. Install Batteries

Slide the batteries chamber’s cover in the direction

of the arrow.

Insert the batteries according to the label inside

battery chamber.

Make sure the direction of the batteries’ polarity is

correct. Close the battery chamber cover in the

direction of the arrow.

2. Mount the speedlite on your camera

Loosen the locking ring by turning it in the direction of the arrow.

Slip the speedlite hot shoe stand into the camera hot shoe stand

until it stops. Turn the locking ring in the direction of the arrow

tighten. To detach the speedlite, loosen the locking ring by turning

it in the opposite direction.

IV. Basic Functions

1. Basic Operations

Operation of the buttons：

Component

Operation

[Power Button]

Power switch of the flash light. The power

of the flash light can be opened or closed

by pressing this button for 2 seconds. It is

suggested that the battery shall be taken

out after the power of the flash light is

turned off through this button.

[Mode Switch

Button]

The mode of the flash light will be switched

among the TTL/M/Multi/S1/S2 in circle for

each press.

[Test Button]

Press the test and the flash will output the

brightness.

[＋]and[－]button

Under the TTL mode, the exposure

compensation can be adjusted through this

button (the flash compensation of the

camera will be covered)

Under the M, Multi, S1 and S2 modes, the

output power of the flash light can be

adjusted through this button

Under the Multi mode, this button can also

be used to adjust the time of the frequency

flash and the frequency. Please refer to the

section of Multi mode.

[Mode Switch

Button]+[－]

Please press the [Mode Switch Button] first

for a while and then press [-]. The switch of

the focus light will turn on or turn off for

each press.

[Mode Switch

Button]+[＋]

Please press the [Mode Switch Button] first

for a while and then press [+]. The flash

light will switch between the front-curtain

synchronization and back-curtain

synchronization for each press.

[Mode

Switch

Button]+[Power

Button]

Please press [Mode Switch Button] first for

a while and then press [Power Button]. The

head focus of the flash light will switch

among the (auto / 24 / 28 / 35 / 50 / 70 / 85) in

circle for each press

Status and meaning of [Charging indicator]

Status

[Charging

Indicator]

Meaning

Operation

The red light

is lit.

The flash light is fully

charged, and can be used.

Normal

The green

light is lit.

The flash light has not been

fully charged.

If the green light is

lit for a long time,

replace the batteries.

The green

light blinks.

The flash light is locked

due to low battery.

Replace the

batteries.

The red and

green lights

blink

alternatively.

The flash light is locked to

prevent overheating due to

frequent flashing.

Wait for about 3

minutes to cool the

flash light.

2. Power-on and Power-off

Turn the switch knob clockwise to turn on the flash light power

supply; at the same time, the flash light is set as TTL mode, the

charging indicator is green and it will turn to red after the charge

is finished many seconds later, which indicates the flash is

available. Continue turning the knob to make the flash light enter

M mode and adjust flash power.

If the charging indicator keeps green for more than 20 seconds,

the flash will power off automatically.

After use, the power of the flash light can be closed by pressing

this button for 2 seconds.

3. TTL Mode

In this mode, the metering system of this camera will detect flash

illumination reflected back from the object so as to automatically

control flash output. When taking photos, you only require aiming

at some scene and press the shutter after focusing, the light will

give proper light as per tips and then you can get your desired

photo.

In the TTL mode, you can also make compensation of flash

brightness with the [Output control knob] within the range of ±3ev,

with the precision of 1/3ev. Please Note that this compensation

setting will override the exposure compensation setting on the

camera.

4. M Mode

In this mode, you can set flash luminance as per your favorite via
【＋】

and 【－】 buttons. When taking photos, you only require

setting the flash luminance, adjust the camera and press the shutter,

the flash light will flash under the camera synchronous signal.

5. Multi Mode

The Multi mode is the stroboflash mode. Under this mode, the

flash light will output the power, flash frequency and time flash

you have set. The power can be adjusted by [+] and [-]. The

adjustment

scope

the

output

power

1/128-1/64-1/32-1/16-1/8-1/4. If you want to adjust the flash time

and flash frequency, please press [+] once firstly and the output

power will shine. Press [Mode Switch Button] that is the MODE

button under this status, the flash time will shine. The flash time

can be adjusted at this time by pressing [+] and [-]. Then press

[Mode Switch Button] again, the flash frequency starts to shine.

The flash time can be adjusted at this time by pressing [+] and [-].

NOTE: The charging speed of the flash light is slow under the

situation that the electricity quantity of the battery is insufficient, which

may cause the occurrence of the high-frequency flash. Please reduce

the flash frequency or change new battery under this situation.

10. Overheating Protection

If the flash light is used too frequently, its overheating protection

function will be triggered, the red and green lights of the charging

indicator will blink alternatively, and the flash light will be locked.

In such case, please wait for three minutes to cancel the protection

before continuing the use.

Please try to use the 1/4 output or lower when rapid shooting is

needed to prevent the effect on the shooting.

11. Auto Zoom

When the flash light is mounted on the camera system supporting

i-TTL/ETTL, the flash light tube will move forward and backward

with the changes of lens focus to suit different illumination zones.

Note: Auto Zoom does not support full frame camera system, but

you may pull out the wide-angle diffuser to avoid vignetting in

photos.

12. Set the focus position of the light head manually

The focus position of the light head can be set manually be

pressing [Mode Switch Button] + [Power Button]. Please press the

[Mode Switch Button] for a while and then press [Power Button].

The light head focus of the flash light will switch among the (auto

/24 / 28 / 35 / 50 / 70 / 85) in circle for each press.

V. Advanced Application

1. Multi-lamp Lighting Application

Use inbuilt flash or top-mounted flash as master flash.

Place speedlite in different directions.

In outdoor application, radio signals

can be reflected by walls; therefore,

the placement of the slave flash

should have more space.

Before placing of the slave flash, test

whether S1/S2 can be synchronous

normally.

Do not place any obstacles between the host flash and the slave

flash, because they may block the transmission of radio signals.

In radio flash mode (S1 or S2), if the flash is idle for 30min, it will

power off automatically in order to save power

2. Exposure Bracketing (FEB)

The FEB function is set on the camera. For the specific setting

method, refer to your Camera Instructions. After the FEB is set,

13. PC synchronous port(for input)

By connecting to the PC synchronous port, you can make the flash

synchronously

the whole overexposure or underexposure; please try to make

adjustments by the camera flash compensation or exposure

compensation settings.

5. You may feel the flash control panel is dim, because there is

one protective film on the panel; you can tear it away to enjoy a

clear visual effect.

6. The flash light is abnormal? Switch off the power of flash

light and camera, mount the flash light on the hot shoe of camera,

and switch on the power of flash light and camera again. If the

abnormity continues, replace the batteries.

7. Precaution for outdoor use of lambency umbrella: The

lambency umbrella mounted on the flash light outdoors may be

blown down easily, and the hot shoe of the flash light may be

broken. Please fix the mounting rack or avoid outdoor use.

8. The S1 and S2 lead flash without the camera failed? The

following situation shall be avoided when the S1 and S2 modes

are used: the wireless touch sensor is directly shined under the sun;

the red eye reduction function of the main light is used; the order

mode (Nikon) or wireless mode (Canon) of the main light is used;

the ST-E2 is used as the flash controller.

The YONGNUO logo in this manual includes the registered

trademark or trademark of SHENZHEN YONGNUO

PHOTOGRAPHY EQUIPMENT Co., Ltd in China or/and other

countries (regions). All other trademarks are the property of their

respective owners.

Shenzhen Yong Nuo Photographic Equipment Co., Ltd
Address: 2-A511 Saige Science & Technology Park, North
Huaqian Rd, Futian District, Shenzhen, China

TEL: 400-001-3888

Website: www.hkyongnuo.com

、电量不足指示

Power low indicator

PC port

YN468-II

USER MANUAL

Please read and understand shis entire manual before

using this product. Keep it for future reference.

-1-

-2-

-3-

-4-

-5-

-6-

-7-

-8-

-9-

-10-

-11-

-10-

-9-

-8-

-7-

-6-

-5-

-4-

-3-

-2-

-1-