Audix D6 AUDIX D6 Leaflet

The D6 is a low impedance microphone and should be plugged into a “mic level” of 

your console, mixer, or recording device. Please note that your microphone does not 

require phantom power and will not be effected in any way by phantom power should 

it be running simultaneously while the microphone is in operation. Avoid plugging or 

unplugging the microphone from the PA system unless the channel is muted or the 

volume of the system turned down. Failure to do so may result in a loud “popping” 

noise which could seriously damage the speakers in the PA system. 

ARCHITECTS AND ENGINEERS SPECIFICATIONS: 

The microphone shall be of the dynamic type operating on the moving coil principle 

and the capsule shall be VLM Type E. The polar pattern of the microphone shall be 

cardioid. The nominal output impedance shall be 200 ohms at 1 kHz. The microphone 

shall have a sensitivity of 0.8 mV / Pa at 80 Hz and will handle a sound pressure level 

of ≥144 dB. The microphone body shall be machined out of aluminum and the grill cap 

shall be steel wire mesh. The overall dimensions shall be 21.5 mm in diameter at the 

base, 51 mm in diameter at the widest point and 117 mm in length. The microphone 

shall be the Audix D6.

The D6 compensates for instruments with extremely high sound pressure levels by 

having a very low output stage. For kick drums, as a general rule, start with the mic 

positioned centered inside the middle of the drum pointed towards the beater. For 

more attack, and less bass boom, move the mic closer to the beater. For less attack 

and more bass, move the mic further away from the beater. For kick drums without 

hole in front head, place the D6 a few inches from the head for a large dynamic sound. 

For toms, position the mic 2 inches from the head and point towards the center of the 

drum. For bass cabinets, position the mic 90 degrees to the grill cloth and 1-2 inches 

inside the edge of the speaker. 

*Further miking techniques may be found on our website at www.audixusa.com

 

D6

IMPORTANT: When miking a kick drum with a sound hole 

in the head, be sure that the D6 is placed INSIDE the 

sound hole. When the head of the grill cap is lined up right 

AT the sound hole, there is extreme air turbulence pushing 

and pulling on the capsule and this can cause failure. For 

more complete miking instructions, go to our web site and 

watch “How to Mic Kick Drum.” 

SERVICE AND WARRANTY:

This microphone is under warranty for a period of 5 years from 

any and all manufacturing defects. Should your microphone 

fail in any way, please contact the Audix Service department 

at 503-682-6933. A Return Authorization number is required 

before returning any products.

CARE AND MAINTENANCE:

The D6 is manufactured to exacting specs with roadworthy construction. 

However, the capsule is highly sensitive and should be handled with care. 

Avoid extreme temperatures and be sure to store your microphone in the 

pouch provided when not in use. Moisture of any kind can adversely affect 

the sound and performance of your microphone. 

***All specifications subject to change without notice.

www.audixusa.com 

503-682-6933 Fax: 503-682-7114 

Audix Corporation 9400 SW Barber St. Wilsonville, OR 97070

Please Check all that apply:

    Male      Female
Age: 

 

Occupation:  

Primary Instruments:       Product to be used for:    

    18 or Under 

   Musician   

   Vocal 

 

        Pro live sound

    19-25   

   Producer   

   Guitar / Bass 

        Pro recording

    26-35   

   Sound Eng. 

   Drums   

        Home recording

    36-45   

   Radio/TV   

   Keyboard  

        Rehearsal

    46-55    

   Production 

   Brass 

 

        Installation

    55 +  

 

   Other _______ 

   Woodwinds 

        School

 

 

 

 

   Strings   

        House of Worship

How did you hear about Audix?  

 

   Other ___________          Other ___________

   Magazine Ad            Online Ad  

   On-line Store            Friend                               Do you own other Audix Products?      Yes      No

   Salesman                 Other __________            Model(s) ________________________________

 

 

 

                  Have you visited the Audix website?     Yes       No  

Please register your product online at www.audixusa.com or mail this form to:

Audix Microphones P.O. Box 4010 Wilsonville, OR 97070

Name:________________________________ Model:___________________

Company:_____________________________ Serial Number:_____________

Address:______________________________ Store:____________________

City:_________________________________  Store Location:_____________

Prov./State:___________ Zip:_____________ Purchase Date:_____________

Phone: (     )___________________________ Signature:_________________

Email:________________________________ Date:____________________ 

ver. 1.2 10/11

LITD6T