Transition Networks SCSCF3014-110 SCSCF3014-110-SA Leaflet

Specifications

Standards 

ANSI, ITU-TS, ETSI, AT&T, G.703, G.921 & G.955

Coax Connectors 

75 ohm coax 

 

 

min: +2.5 dBm 

min: -9.7dBm 

max: +9.1 dBm 

max: +10.5 dBm

Fiber Connectors 

SFP: LC connector Uses standard 100BASE-X/OC-3 SFP 

Data Rates 

DS3/T3 = 44.7 Mbps; E3 = 34.4 Mbps;  

STS-1 = 51.8 Mbps

Status LED 

Power, Coax link status, coax loop-back status, AIS on 

coax link; Fiber link status, fiber loop-back status,  

AIS on fiber link

Dimensions 

Width: 3.25” [83 mm];  

Depth: 4.7” [119 mm];  

Height: 1.0” [25 mm]

Power Consumption 

3.0 Watts

Power Supply 

12 VDC, 0.8 Amp (minimum)

Environment  

Operating Temperature -10° to 65°C (14° to 149°F) 

Humidity 5-95% non-condensing  

Storage Temperature -20º to 85ºC (-4º to 185ºF) 

Shipping Weight  

2.0 lbs. [0.90 kg]

Regulatory Compliance 

CISPR/EN55022 Class A; FCC Class A; CE Mark

MTBF w/ Power Supply 

Greater than 41,660 hours (MIL-HDBD-217F) 

Greater than 114,580 hours (Bellcore)

MTBF w/o Power Supply  Greater than 250,000 hours (MIL-HDBD-217F) 

Greater than 687,000 hours (Bellcore)

Warranty  

Lifetime 

 

see also: 

DS3-T3/E3 Point System™ Slide-In-Module NID  

The DS3 – T3/E3 & STS-1 copper to fiber network 
interface device (NID) provides a solution for those 
users that need to extend DS3 connections over 
fiber.  
The DS3 – T3/Es & STS-1 supports Small Form Plug-
gable (SFP) transceivers to support a variety of fiber 
types, distances and wavelengths to provide maxi-
mum flexibility across a variety of network topolo-
gies.  The use of Coarse Wave Division Multiplexing 
(CWDM) SFPs can be utilized to further increase the 
bandwidth capacity of the fiber infrastructure.
The DS3 – T3/E3 & STS-1 NID must be used in 
pairs*.  A typical installation will include a chassis 
card [CCSCF, pg 55] installed in the Point Sys-
tem™ locally and a stand-alone device installed at 
the remote location.

Optional Accessories (sold separately)

   Piggy Back Power Supply

   Stand-Alone Power Supply

   12-Slot Media Converter Rack

   DIN Rail Bracket 5.0” [127 mm]

   DIN Rail Bracket (flat) 3.3” [84 mm]

   Wall Mount Bracket 4.0” [102 mm]

   Vertical Wall Mount Bracket 5.0” [127 mm]

   4-Slot Media Converter Shelf

Features

4

AIS (Alarm Indication Signal)

4

Coax Line Build Out

4

Switch selectable for DS3/T3 or E3

4

Loopback – Coax and Fiber 

4

LEDs for immediate visual status

4

Supports dual or single fiber

4

Supports multimode and single mode    

    fiber at a variety of distances

4

Supports CWDM SFPs

Integrate Voice & Data on Fiber Network

Ordering Information

  (2) Coax (BNC)

to 1300nm multimode (ST)

 

  (2) Coax (BNC)

to 1300nm multimode (SC)

  (2) Coax (BNC)

to 1310nm single mode (SC)

  (2) Coax (BNC)

to 1310nm single mode (SC)

 

  (2) Coax (BNC)

to 1310nm single mode (SC)

  (2) Coax (BNC)

to 1550nm single mode (SC)

  (2) Coax (BNC)

to SFP slot (empty)

Recommended use in pairs 

  (2) Coax (BNC)

to 1310nm TX/1550nm RX single fiber    

single mode (SC)

  (2) Coax (BNC)

to 1550nm TX/1310nm RX single fiber    

single mode (SC)

  (2) Coax (BNC)

to 1310nm TX/1550nm RX single fiber    

single mode (SC)

  (2) Coax (BNC)

to 1550nm TX/1310nm RX single fiber    

single mode (SC)

  (2) Coax (BNC)

to 1310nm TX/1550nm RX single fiber    

single mode (SC)

  (2) Coax (BNC)

to 1550nm TX/1310nm RX single fiber    

single mode (SC)

  (2) Coax (BNC)

to 1310nm TX/1550nm RX single fiber

  single mode (SC)

  (2) Coax (BNC)

to 1550nm TX/1310nm RX single fiber

  single mode (SC)

*The SCSCF30xx-110 will only work with 

another CCSCF30xx-110 or SCSCF30xx-110.  

The product does not work with a -10x model.