Audix I5 AUDIX I5 Leaflet

Product codes
AUDIX I5
Page of 2
SPECIFICATIONS:
ARCHITECTS AND ENGINEERS SPECIFICATIONS:
The microphone shall be of the dynamic type operating on the moving coil principle and the polar 
pattern of the microphone shall be cardioid. The capsule shall be VLM Type B. The nominal out-
put impedance shall be equal to 150 ohms at 1 kHz. The microphone shall have a sensitivity of 
1.5  mV / Pa at 1 kHz and a sound pressure level  ≥140 dB. The microphone body and grill shall 
be of die cast zinc alloy.  The overall dimensions shall be 23 mm in diameter at the base, 37.5 mm 
at the top, and 141.5 mm in length. The microphone shall be the Audix i5.
Transducer Type   
                          Dynamic
Frequency Response                           50 Hz  - 16 kHz 
Polar Pattern        
                          Cardioid 
Output Impedance                                       150 ohms 
Sensitivity                                               1.5 mV / Pa @ 1k
Capsule Technology 
                      VLM Type B
Off Axis Rejection                                          > 23 dB
Maximum SPL                                          ≥ 140 dB                       
Power Requirements                                       None
Connector 
                                 Switchcraft® or Audix  
    male 
XLR 
connector
Polarity                                               Positive voltage on pin
                                                              2 relative to pin 3 of
                                                            output XLR connector
Housing / Finish                                  Die cast Zinc Alloy /
 
 
 
 
     Black E-coat
Weight                                                   183 g / 6.5 ounces
Length                                                141.5 mm / 5.6 inches
 
OPERATION:
The i5 is a low impedance microphone and should be plugged into a “mic level” input on your 
console, mixer, or recording device. Please note that your microphone does not require phantom 
power and will not be effected in any way by phantom power should it be running simultaneously 
when the microphone is in operation. Avoid plugging or unplugging the microphone from the PA 
system unless the channel is muted or the volume of the system turned down. Failure to do so 
may result in a loud “popping” noise which could seriously damage the speakers in the PA system.    
 
FREQUENCY / POLARS:
USER TIPS:
The i5  has a  tight (cardioid) pick-up pattern in order to help eliminate sound from other instruments 
on stage from “bleeding” into the microphone. For this reason, it the i5 is exceptionally effective for  
drums and percussion in be able to capture the sound of each component of the kit.   
Snare: Start with the i5 about 2 inches above the head and aimed towards the center of the drum. 
For more “rim” effect, the i5 can be aimed less towards the center and more towards the rim. It is 
not uncommon for engineers to place the mic practically right on the drum head to achieve a very 
tight, cracking sound. 
Toms, congas: Similar to snare. For tighter sound and more attack place, the mic closer to the 
head. For more decay and overtones pull the mic further away from the head. 
Guitar cabs: The i5 can be placed within 1-2 inches of the grill cover at a 90 degree angle pointing 
directly into the speaker. If the mic is placed closer to the edge of the speaker, you will minimize 
the higher frequencies and get a warmer, fatter tone. To capture more highs, move the mic closer 
towards the center of the speaker, but avoid the middle of the speaker. 
Horns: Place the mic within 1-3 inches of the bell, especially when on a stage with drums, bass, 
guitar, etc. For jazz, classical, and music where the stage volume is lower, the mic can be placed 
further away for a richer, fuller, sound.
Allow a distance of 2-3 feet between microphones to avoid phase cancellation issues. 
*Further miking techniques may be found on our website at www.audixusa.com
DIMENSIONS (mm):
i5
SERVICE AND WARRANTY:
This microphone is under warranty for a period of 5 years from 
any and all manufacturing defects. Should your microphone 
fail in any way, please contact the Audix Service department 
at 503-682-6933. A Return Authorization number is required 
before returning any products.
CARE AND MAINTENANCE:
The i5 is manufactured to exacting specs with roadworthy construction. 
However, the capsule is highly sensitive and should be handled with care. 
Avoid extreme temperatures and be sure to store your microphone in the 
pouch provided when not in use. Moisture of any kind can adversely affect 
the sound and performance of your microphone. 
***All specifications subject to change without notice.
www.audixusa.com 
503-682-6933 Fax: 503-682-7114 
Audix Corporation 9400 SW Barber St. Wilsonville, OR 97070
AUDIX WARRANTY REGISTRATION FORM
Please Check all that apply:
    Male      Female
Age: 
 
Occupation:  
Primary Instruments:       Product to be used for:    
    18 or Under 
   Musician   
   Vocal 
 
        Pro live sound
    19-25   
   Producer   
   Guitar / Bass 
        Pro recording
    26-35   
   Sound Eng. 
   Drums   
        Home recording
    36-45   
   Radio/TV   
   Keyboard  
        Rehearsal
    46-55    
   Production 
   Brass 
 
        Installation
    55 +  
 
   Other _______ 
   Woodwinds 
        School
 
 
 
 
   Strings   
        House of Worship
How did you hear about Audix?  
 
   Other ___________          Other ___________
   Magazine Ad            Online Ad  
   On-line Store            Friend                               Do you own other Audix Products?      Yes      No
   Salesman                 Other __________            Model(s) ________________________________
 
 
 
                  Have you visited the Audix website?     Yes       No  
Please register your product online at www.audixusa.com or mail this form to:
Audix Microphones P.O. Box 4010 Wilsonville, OR 97070
Name:________________________________ Model:___________________
Company:_____________________________ Serial Number:_____________
Address:______________________________ Store:____________________
City:_________________________________  Store Location:_____________
Prov./State:___________ Zip:_____________ Purchase Date:_____________
Phone: (     )___________________________ Signature:_________________
Email:________________________________ Date:____________________ 
1.1
LITI5T