HGST HCS5C3232SLA380 User Manual
HITACHI CinemaStar 5K 320 Hard Disk Drive specification (Rev 1.21)
160
Completion Time Limit event if some data transferred is in error.
Output Parameters To The Device
Feature Current
URG (bit7)
URG specifies an urgent transfer request. The Urgent bit specifies that the
command should be completed in the minimum possible time by the device and
shall be completed within the specified Command Completion Time Limit.
command should be completed in the minimum possible time by the device and
shall be completed within the specified Command Completion Time Limit.
RC (bit6)
RC specifies Read Continuous mode enabled. If the Read Continuous bit is set
to one, the device shall not stop execution of the command due to errors.
If the RC bit is set to one and errors occur in reading or transfer of the data, the
device shall continue to transfer the amount of data requested and then provide
ending status with BSY bit cleared to zero, the SE bit set to one, the ERR bit
cleared to zero, and the type of error, ICRC, UNC, IDNF or ABRT reported in the
error log.
If the RC bit is set to one and the CCTL expires, the device shall stop execution
of the command and provide ending status with the BSY bit cleared to zero, the
SE bit set to one, the ERR bit cleared to zero, and report the fact that the CCTL
expired by setting the CCTO bit in the error log to one.
In all cases, the device shall attempt to transfer the amount of data requested
within the CCTL even if some data transferred is in error.
to one, the device shall not stop execution of the command due to errors.
If the RC bit is set to one and errors occur in reading or transfer of the data, the
device shall continue to transfer the amount of data requested and then provide
ending status with BSY bit cleared to zero, the SE bit set to one, the ERR bit
cleared to zero, and the type of error, ICRC, UNC, IDNF or ABRT reported in the
error log.
If the RC bit is set to one and the CCTL expires, the device shall stop execution
of the command and provide ending status with the BSY bit cleared to zero, the
SE bit set to one, the ERR bit cleared to zero, and report the fact that the CCTL
expired by setting the CCTO bit in the error log to one.
In all cases, the device shall attempt to transfer the amount of data requested
within the CCTL even if some data transferred is in error.
NS (bit5)
NS (Not Sequential) may be set to one if the next read stream command with the
same Stream ID may not be sequential in LBA space.
same Stream ID may not be sequential in LBA space.
HSE (bit4)
HSE (Handle Stream Error) specifies that this command starts at the LBA of the
last reported error for this stream, so the device may attempt to continue its
corresponding error recovery sequence where it left off earlier.
last reported error for this stream, so the device may attempt to continue its
corresponding error recovery sequence where it left off earlier.
Stream ID (bit 0..2)
Stream ID specifies the stream to be read. The device shall operate according
to the Stream ID set by the Read Stream command.
to the Stream ID set by the Read Stream command.
Feature Previous
CCTL (7:0)
CCTL (7:0)
The time allow
ed for the current command‘s completion is calculated as follows:
Command Completion Time Limit = (content of the Feature register
Previous) * (Identify Device words (99:98)) useconds
If the value is zero, the device shall use the Default CCTL supplied with a
previous Configure Stream command for this Stream ID. If the Default CCTL
is zero, or no previous Configure Stream command was defined for this Stream
ID, the drive will ignore the CCTL. The time is measured from the write of the
command register to the final INTRQ for command completion. The device has
minimum CCTL value. When the specified value is shorter than the minimum
value, CCTL is set to the minimum value. Actual minimum CCTL value is
described in the
Previous) * (Identify Device words (99:98)) useconds
If the value is zero, the device shall use the Default CCTL supplied with a
previous Configure Stream command for this Stream ID. If the Default CCTL
is zero, or no previous Configure Stream command was defined for this Stream
ID, the drive will ignore the CCTL. The time is measured from the write of the
command register to the final INTRQ for command completion. The device has
minimum CCTL value. When the specified value is shorter than the minimum
value, CCTL is set to the minimum value. Actual minimum CCTL value is
described in the
―Deviations from Standard‖ section.
Sector Count Current
The number of continuous sectors to be transferred low order, bits (7:0)
Sector Count Previous
The number of continuous sectors to be transferred high order, bits (15:8). If
zero is specified in the Sector Count register, then 65,536 sectors will be
transferred.
zero is specified in the Sector Count register, then 65,536 sectors will be
transferred.
Sector Number Current
LBA (7:0).
Sector Number Previous
LBA (31:24).
Cylinder Low Current
LBA (15:8).
Cylinder Low Previous
LBA (39:32).
Cylinder High Current
LBA (23:16).
Cylinder High Previous
LBA (47:40).
Input Parameters From The Device
Sector Number (HOB=0)
LBA (7:0) of the address of the first unrecoverable error.
Sector Number (HOB=1)
LBA (31:24) of the address of the first unrecoverable error.
Cylinder Low (HOB=0)
LBA (15:8) of the address of the first unrecoverable error.