Panasonic WV-NP1000 Leaflet

• CD-ROM* .......................................1 pc.

• Operating Instructions

  (English version) ........................... 1 pc.

• ALC lens connector cap ............... 1 pc.

• Power cord

  (only for the WV-NP1000) ............. 1 pc.

The following is for the installation.

• Cord label ..................................... 1 pc.

* The IP setting software, the viewer software and 
  the network operating instructions (PDF) are 
  included on the CD-ROM.

• MPEG-4/JPEG digital signal output at VGA image size with up to 30 ips
• MPEG-4 and JPEG dual stream output for simultaneous real time 

monitoring and high resolution recording 

• Progressive output provides clear images, even when the subject is moving.
• High sensitivity with Day/Night function: 1.0 lux (Color), 0.06 lux 

(B/W) at F1.4. IR cut filter switches on/off to enhance the sensitivity 
in B/W mode.

• Adaptive Digital Noise Reduction: Integration of 2D-DNR and 3D-

DNR ensures noise reduction in various conditions.

• Electronic sensitivity enhancement: Auto (Up to 10x) / Manual (Up to 32x)
• Electronic shutter: Up to 1/10,000 sec.
• VMD (Video Motion Detector) with 4 programmable detection areas 

and 3 sensitivity levels.  

• Up to 8 Privacy zones
• Auto Image Stabilizer for applications where vibration or wind is a concern.
• Flexible digital zoom and pan/tilt operation: Up to 5x variable digital 

zoom and pan/tilt can be set in the setup menu or controlled by a 
system controller (effective both for analog and network video).      
2x or 4x digital zoom and pan/tilt can be controlled by the browser 
GUI for network video. 

• Internal / Multiplexed Vertical Drive (VD2) synchronization
• Camera title displays: Up to 16 (OSD) and 20 (on browser) 

alphanumeric characters

• SD Memory card slot for alarm recording and backup upon network 

failure. Recorded dada can be downloaded by using FTP command.

• ABF (Auto Back Focus) ensures easy installation and stable focus in 

both color and B/W modes.

• Alarm sources including Terminal input, VMD and Panasonic alarm 

command can trigger actions including SD memory recording/FTP 
image transfer, E-mail notification, Alarm indication, Terminal output 
and Panasonic protocol output.

• Built-in microphone for audio (1-way)
• Built-in network interface (10Base-T / 100Base-TX)

• Multiscreen: Images from 8 cameras can be displayed in 2 separate 

Quad screens (JPEG only). 20 characters camera title is available 
for each camera.

• FTP client function enables periodic image data transfer or transfer 

upon alarm.

• Alarm e-mail notification
• Max. bit rate/client for MPEG-4 (64 / 128 / 256 / 512 / 1,024 / 1,536 / 

2,048 / 3,072 / 4,096 kbps) and Total bit rate control (64 / 128 / 256 / 
512 / 1,024 / 2,048 / 4,096 kbps / 10 Mbps / Unlimited) allowing 
flexible network management.

• Supported Protocol: TCP/IP, UDP/IP, HTTP, RTP, FTP, SMTP, 

DHCP, DNS, DDNS, NTP, SNMP

• Multi-language GUI and setup menu: English, French, Italian, 

Spanish, German, Russian, Chinese (PAL) / English, French 
(NTSC)  

* Installation required except for English

1/3 inch High Resolution 2x Varifocal Lens

(2.8 ~ 6 mm)
F1.4 (Wide)
F2.1 (Tele)

Lens: optional