Sony Streaming Receiver Adaptor BKMFW50 User Manual
Product codes
BKMFW50
9
3
Press the MENU button on the
display to bring up the main menu.
display to bring up the main menu.
4
Use the
M/m buttons to select
“INITIAL SETUP/
INFORMATION” and press the
ENTER button. The “INITIAL
SETUP/INFORMATION” menu
appears.
INFORMATION” and press the
ENTER button. The “INITIAL
SETUP/INFORMATION” menu
appears.
5
Use the
M/m buttons to select “IP
Address Setup” and press the ENTER
button.
button.
6
Use the
M/m buttons to select
“DHCP” and press the ENTER
button.
button.
7
Use the
M/m buttons to select
“Execute” and press the ENTER
button.
button.
Checking the automatically
assigned IP address
assigned IP address
When an IP address has been automatically
assigned, you can call up the display
control screen of the BKM-FW50 as
follows and check which IP address has
been assigned. The IP address changes each
time power to the display is turned on.
Therefore you must check the IP address as
described here every time after turning
power to the display off and on again.
assigned, you can call up the display
control screen of the BKM-FW50 as
follows and check which IP address has
been assigned. The IP address changes each
time power to the display is turned on.
Therefore you must check the IP address as
described here every time after turning
power to the display off and on again.
1
Press the MENU button on the
display to bring up the main menu.
display to bring up the main menu.
2
Select “INITIAL SETUP/
INFORMATION” and check the IP
address that is displayed in the “IP
address” field.
INFORMATION” and check the IP
address that is displayed in the “IP
address” field.
Computer Operation
Computer Operation
Controlling the display
You can make various display settings on
the screen of the computer.
Make sure that the BKM-FW50 is properly
installed in the display, and that the BKM-
FW50, computer, and router or hub are
properly connected with network cable.
Then turn on power to the display, the
computer, and the router or hub.
There are five display screens, divided by
function: “Information” screen,
“Configure” screen, “Control” screen,
“Player” screen, and “Setup” screen.
the screen of the computer.
Make sure that the BKM-FW50 is properly
installed in the display, and that the BKM-
FW50, computer, and router or hub are
properly connected with network cable.
Then turn on power to the display, the
computer, and the router or hub.
There are five display screens, divided by
function: “Information” screen,
“Configure” screen, “Control” screen,
“Player” screen, and “Setup” screen.
For details on button functions, consult the
operating instructions of the FWD series
product.
operating instructions of the FWD series
product.
1
Start the browser of the computer
(Internet Explorer 6.0 or later).
(Internet Explorer 6.0 or later).
2
Enter the IP address that was assigned
to the display control function into the
address field, in the format “http://
xxx.xxx.xxx.xxx”. Then press the
Enter key on the keyboard.
When a user name and password
have been set, the “Network
Password” screen appears. Enter the
user name and password that were
set, and then proceed to the next step.
to the display control function into the
address field, in the format “http://
xxx.xxx.xxx.xxx”. Then press the
Enter key on the keyboard.
When a user name and password
have been set, the “Network
Password” screen appears. Enter the
user name and password that were
set, and then proceed to the next step.
3
Click the function tab at the top of the
screen and select the desired screen.
screen and select the desired screen.
Setting items on respective
screens
screens
Information screen
This screen shows the model name, serial
number and other display information, as
well as the power status and the input
signal selection.
The screen is for information only. There
are no items that can be set.
number and other display information, as
well as the power status and the input
signal selection.
The screen is for information only. There
are no items that can be set.