Perfectpro Rockbull 8717774762059 Data Sheet

G B

1.  Place the radio on a flat surface.

2.  Carefully extend the antenna located on the top of the radio. Adjust the antenna so  

 

it is vertically extending above the radio.

3.  Plug the AC power cord into the AC socket. The radio will start up and the display  

 

will show “Welcome To Digital Radio” for a few seconds. Then the radio will    

 

automatically perform an auto scan of the Band III DAB channels and the FM band.  

 

The display will show “Scanning” in DAB and “Auto” in FM.

4.  When the scan is completed, the 10 strongest stations of DAB and FM will be  

 

stored as presets. The radio will switch to standby with the updated clock and date  

 

showing on the display.

5.  If no signals are found, the clock will not be updated. It may be necessary to   

 

relocate the radio to a position with better reception.

1.  Carefully extend the antenna. Press the 

On/Off button to switch on the radio.

2.  Select DAB by pressing the 

SOURCE button.

3.  The first station in the list of stations found will be played. The display will show

 

the station name. If the radio has been used before, the last used station will be  

 selected.

4.  If no DAB signals are detected, “No stations available” will be displayed. It may  

 

be necessary to relocate the radio to a position with better reception. You should  

then carry out an auto scan to find stations, please refer to the section

stations - DAB”. 

1.  Press the 

On/Off button to switch on the radio. The display will show “Connecting”  

 

and  “Playing” for a few seconds.

2.  The display shows the name of the radio station currently selected.

3.  Rotate the 

TUNING knob to scroll through the list of available stations.

4.  When the desired station name appears on the display, press the 

TUNING knob to  

 

select the station. 

Note: If after selecting a station the display shows “No stations available”, it may be 

necessary to relocate the radio to a position with better reception. 

In DAB mode, the radio can display a range of information on the display.

Press the 

INFO button to cycle through the various modes. 

 

a. Scrolling text  

Displays scrolling text message e.g. station information,  

 

 

artist/track name, phone-in number, etc.

 

b. Signal strength  

Displays the signal strength of radio reception. The  

clear unfilled rectangle indicates minimum signal level

 

 

required for satisfactory reception. 

 

c. Program type  

Displays the type of station being listened to e.g. Pop,  

 

 

Classic, News, etc.

 

d. Multiplex name  

Displays the name of multiplex to which the current  

 

 

station belongs.

 

e. Channel & frequency   Displays the channel number and frequency for the  

 

 

currently tuned DAB station.

 

f. Bit rate & audio format   Displays the digital audio bit rate and audio format. 

 

g. Time & date  

Displays the current time and date. 

From time to time, new stations may become available. You may proceed to find new

stations as follows: 

1.  In DAB mode, press the 

MENU button, “Full Scan” shows on the display. 

2.  Press the 

TUNING knob, the radio will perform a scan of the Band III DAB    

 

channels. As new stations are found, the station counter on the right-hand side of  

 

the display will increase and new radio stations found will be added to the list stored  

 

in the radio.

Manual tuning is an alternative method of finding new stations. Instead of scanning the

entire Band III channels automatically, you may tune the radio directly to a known DAB 

channel and store all the multiplex in that channel into the available station list. 

1.  In DAB mode, press the 

MENU button and rotate the TUNING knob until the LCD  

 

display shows “Manual tune”, then press the 

TUNING knob. The display will show  

 

DAB channel and Frequency. 

2.  Rotate the 

TUNING knob to select the desired Channel or Frequency and then  

 

press the 

TUNING knob to tune to the chosen frequency. 

3.  When DAB stations in the tuned channel are found, the display will show the name  

 

of the station. Any new radio stations found will be added to the list stored in the radio. 

4.  The signal strength display shows the reception of the station. The clear unfilled

 

rectangle indicates minimum signal level required for satisfactory reception. The  

 

signal strength bars will go up or down showing the changing signal strength as you  

 

adjust the antenna or the radio position.