Albrecht BPA 300 15510 User Manual
Product codes
15510
Precautions
The adaptor should not be used in the close neighbourhood or with direct mechanical contact
to other transmitting devices – interferences or operation errors might occur.
to other transmitting devices – interferences or operation errors might occur.
The adapter can be charged from the 230 V power network or via special DC charging adaptor
cable (optional available under order No. 15403) from the 12 V motor bike board network.
cable (optional available under order No. 15403) from the 12 V motor bike board network.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modification to this equipment; such modifications could void the users authority to use this
equipment
modification to this equipment; such modifications could void the users authority to use this
equipment
Getting ready
Charging the wireless adapter
Completely charge the internal Lithium Polymer battery for at least 2- max.4 hours before using
the set for the first time. Insert the DC charging plug of the wall charger into the adapter and
connect the wall charger to an AC outlet. The LED will be red during charging and will be off
after charging is completed. The charging process will be automatically terminated at full
battery condition, so over-charging is not possible. Please do not use any other wall charger
than the supplied charger. Other chargers may not support the automatic charge termination at
the end of the charging process and may cause severe problems and fire or injury risks
through burning or exploding batteries.
the set for the first time. Insert the DC charging plug of the wall charger into the adapter and
connect the wall charger to an AC outlet. The LED will be red during charging and will be off
after charging is completed. The charging process will be automatically terminated at full
battery condition, so over-charging is not possible. Please do not use any other wall charger
than the supplied charger. Other chargers may not support the automatic charge termination at
the end of the charging process and may cause severe problems and fire or injury risks
through burning or exploding batteries.
When the battery is running low during operation, the LED indicator will flash
. When the
low power alert is displayed, you will have approximately 10 minutes of talk time remaining
before the battery runs out completely.
The battery can be charged anytime without the need of full discharging. Be sure to charge the
headset at room temperature. The battery may not be properly charged if the temperature is
too high or too low.
After unplugging the headset from the charger, please avoid placing the set in locations of high
temperature or direct sunlight, i.e. above the gas tank of a motorcycle or under the windshield
of a car.
I Please do not attempt to replace the battery of the adapter set. The battery is soldered and
can only be replaced by authorized service partners.
You may answer an incoming call only if the battery has sufficient power while charging.
before the battery runs out completely.
The battery can be charged anytime without the need of full discharging. Be sure to charge the
headset at room temperature. The battery may not be properly charged if the temperature is
too high or too low.
After unplugging the headset from the charger, please avoid placing the set in locations of high
temperature or direct sunlight, i.e. above the gas tank of a motorcycle or under the windshield
of a car.
I Please do not attempt to replace the battery of the adapter set. The battery is soldered and
can only be replaced by authorized service partners.
You may answer an incoming call only if the battery has sufficient power while charging.
Connecting the adapter with the wired headset
You can plug the 6 pin male plug of the wired helmet set into the 6 pin female plug of the
adapter. The helmet set can be ALBRECHT CHS 300, OHS 500, OHS 550. Other headsets
like MHS 300 or MHS 301 headsets can be connected only if already equipped with 6 pin male
plugs. MIDLAND Headsets like MA 46 and other brands do not fit, even if they may use the
same connector type!
You can plug the 6 pin male plug of the wired helmet set into the 6 pin female plug of the
adapter. The helmet set can be ALBRECHT CHS 300, OHS 500, OHS 550. Other headsets
like MHS 300 or MHS 301 headsets can be connected only if already equipped with 6 pin male
plugs. MIDLAND Headsets like MA 46 and other brands do not fit, even if they may use the
same connector type!
Turning the adapter set on and off
Turning on the adapter:
•
Press and hold the button for approximately 3 sec. until the LED will flash 3 x green