Manualsbrain.com
  1. Manuals
  2. Brands
  3. Panasonic
  4. QM4HSU2C240VJ Time Delay Relay, Timer, 1 voltage-free CO (Monofunctional) on-delay 100 - 240 V/AC/DC IP40 / IP
  5. Data Sheet

Panasonic QM4HSU2C240VJ Time Delay Relay, Timer, 1 voltage-free CO (Monofunctional) on-delay 100 - 240 V/AC/DC IP40 / IP QM4HSU2C240VJ Data Sheet

Product codes
QM4HSU2C240VJ
Download
Page of 3
QM4H
46
DIMENSIONS
QM4H-S
TIMER
MODE
INST.
T.D.
+
-
-
+
-
+
-
+
8
8
8
S
TIMER
QM4H-G
+
-
8
-
+
8
-
+
8
-
+
S
48
1.890
72.5
2.854
44.5
1.752
(85.4)
(3.362)
6
.236
9.5
.374
12.9
.508
• S Type
• G Type
Panel cut-out dimensions
Dimensions A when n products 
are installed continuously:
A = (48
∗n–2.5     )
+0.6
0   
A = (1.890
∗n–.098      )
+.024
0     
A
45
+0.6
0   
1.772
+.024
0     
45
+0.6
0   
1.772
+.024
0     
45
+0.6
0   
1.772
+.024
0     
Panel Mounting Diagram
Panel (Thickness: 1 to 5 mm .039 to 
.197 inch
)
Mounting frame (AQM4812: supplied)
(AT8-DA4 can also be used for 
mounting frame. Sold separately)
Mounting screw 
(supplied with mounting frame)
Terminal layouts and Wiring diagrams
• QM4H-S Type
3
2
1
8
7
6
5
4
MODE
NC
NO
COM
NC
NO
Operating
voltage
COM
MODE
T.D.
INST.
TD mode: Time delay 2C
INST mode: 
Time delay 1C and 
Instantaneous 1C
*Use MODE switch on front
Notes:
1. Operating voltage signs in parentheses ( ) indicate the polarity 
of the DC type.
2.         is a time delay contact.
        is an instantaneous contact.
• QM4H-G Type
Operating
voltage
4
5
6
7
8
1
2
3
NO
NC
COM
RESET
STOP
COM
(units: mm 
inch
)
Tolerance: 
±1.0 
.039
OPERATION MODE
• QM4H-S Type
1) T.D. mode
2) INST. mode
ON
T
ON
OFF
OFF
Power supply
Time delay contact 
(N.O. contact)
1-3 or 6-8
OP.LED
ON
ON
T
ON
OFF
OFF
OFF
Power supply
Time delay contact 
(N.O. contact) 6-8
Instantaneous contact 
(N.O. contact) 1-3
OP.LED
• QM4H-G Type
* Set the reset inputs 1 to 3 and stop inputs 1 to 4 to 20 ms or higher.
* When shorting a signal, please set the inter-terminal resistance to 1 k
Ω or less, 
and the inter-terminal residual voltage to 2 V or less. 
When releasing, please set the inter-terminal resistance to 100 k
Ω or greater.
ON
Power supply
Lit
Blinking
Blinking slowly
OP.LED
ON
ta
t1
t2
T
ON
Reset 1-3
Stop 1-4
Time delay contact 
(N.O. contact) 6-8
ON
T: Setting time    t1+t2 = T    ta<T
ON
ON
PRECAUTIONS IN USING THE QM4H
1. Avoid locations subject to flammable 
or corrosive gases, excessive dust, oil, 
vibrations, or excessive shocks.
2. Since the main-unit is made of 
polycarbonate resin, avoid contact with or 
use in environments containing methyl 
alcohol, benzene, thinners, and other 
organic solvents; and ammonia, caustic 
sodas, and other alkaline substances.
3. Power supply superimposed surge 
protector
Although a surge protector will withstand 
standard-waveform voltage with the 
values in the next table, anything above 
this will destroy the internal circuit. You 
should therefore use a surge absorber.
• Surge waveform
[
±(1.2×50) µs uni-polar full wave voltage]
4. In order to maintain the characteristics, 
do not remove the timer case.
5. When installing the panel, use the 
supplied AQM4812 main-unit 
mounting frame. Note that the AT8-DA4 
is also available for sale separately.
6. If you change the operating voltage, 
be sure not to allow leak current into 
the timer.
7. Avoid leaving the unit powered 
continuously. Leaving the unit 
powered up with output set to ON 
continuously for a long period of time 
(about 1 month or more) will wear out 
the electronic components. If you will 
be keeping it powered continuously, 
combine with a relay to create the 
circuit shown below:
12 to 48 V AC/DC
100 to 240 V AC/DC
1,000 V
6,000 V
R
T
R
R
T
qm4h.fm  Seite 46  Donnerstag, 1. Juli 2004  3:10 15
07/2004