MEAN WELL SDR-480-24 Data Sheet

1500ms, 150ms/230VAC          3000ms, 150ms/115VAC at full load

14ms/230VAC at full load

90 ~ 264VAC          127 ~ 370VDC

47 ~ 63Hz

94%

0.94/230VAC          0.99/115VAC at full load

5A/115VAC          2.5A/230VAC

56 ~ 65V

40A/115VAC          80A/230VAC

<0.8mA / 240VAC

29 ~ 33V

Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery

105

5

 (TSW : detect on heatsink of power switch)

℃± ℃

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

UL508, TUV EN60950-1 approved

Compliance to EN55011, EN55022 (CISPR22), EN61204-3 Class B, EN61000-3-2,-3

-25 ~ +70

 (Refer to "Derating Curve")

℃

60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load

20 ~ 95% RH non-condensing

-40 ~ +85

, 10 ~ 95% RH

℃

±

℃

℃

0.03%/

 (0 ~ 50

)

Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6

112.9K hrs min.      MIL-HDBK-217F (25

)

℃

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), EN61204-3, heavy industry level, criteria A,
SEMI F47, GL approved

85.5*125.2*128.5mm (W*H*D)

1.6Kg; 8pcs/13.8Kg/0.9CUFT

48V

10A

0 ~ 10A

480W

15A

120mVp-p

48 ~ 55V
±1.0%
±0.5%
±1.0%

24V

20A

0 ~ 20A

480W

30A

720W (3sec.)

100mVp-p

24 ~ 28V
±1.2%
±0.5%
±1.0%

■

 Features :

I/P-O/P:3KVAC     I/P-FG:2KVAC     O/P-FG:0.5KVAC     O/P-DC OK:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25

/ 70% RH

℃

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25  of ambient temperature.

℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
    EMC directives.
5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power.
    In case the adjacent device is a heat source, 15mm clearance is recommended.
6. 3 seconds peak power max. and the average output power should not exceed the rate power.
7. Derating may be needed under low input voltage. Please check the derating curve for more details.

480W Single Output Industrial DIN RAIL with PFC Function

‧

High efficiency 94% and low power dissipation

‧

150% peak load capability

‧

Built-in active PFC function, PF>0.94

‧

Protections: Short circuit / Overload / Over voltage / Over temperature                         

‧

Cooling by free air convection

‧

Built-in constant current limiting circuit

‧

Can be installed on DIN rail TS-35/7.5 or 15

‧

UL 508(industrial control equipment)approved

‧

EN61000-6-2(EN50082-2) industrial immunity level

‧

Built-in DC OK relay contact

‧

100% full load burn-in test

‧

3 years warranty

Normally works within 110 ~ 150% rated output power for more than 3 seconds and then shut down o/p voltage with auto-recovery

>150% rated power, constant current limiting with auto-recovery within 2 seconds and may cause to shut down if over 2 seconds