MEAN WELL SDR-240-24 Data Sheet

1500ms, 60ms/230VAC          3000ms, 60ms/115VAC at full load

20ms/230VAC          20ms/115VAC at full load

88 ~ 264VAC          124 ~ 370VDC

47 ~ 63Hz

89%

0.93/230VAC          0.96/115VAC at full load

1.4A/115VAC          0.7A/230VAC

29 ~ 33V

91%

56 ~ 65V

90.5%

35A/115VAC          70A/230VAC

<1mA / 240VAC

Normally w

 more than 3 

 and then shut down o/p voltage

orks within 110 ~ 150% rated output power for

seconds

14 ~ 17V

>150% rated power, constant current limiting with auto-recovery within 3 seconds and shut down o/p voltage after 3 seconds

Protection type : Shut down o/p voltage, re-power on to recover 

95

5

 (TSW) detect on heatsink of power switch

℃± ℃

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

UL508, TUV EN60950-1 approved

Compliance to EN55011, EN55022 (CISPR22), EN61204-3 Class B, EN61000-3-2,-3

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), EN61204-3, heavy industry level, criteria A,
SEMI F47, GL approved

-25 ~ +70

 (Refer to "Derating Curve")

℃

60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load

20 ~ 95% RH non-condensing

-40 ~ +85

, 10 ~ 95% RH

℃

±

℃

℃

0.03%/

 (0 ~ 50

)

Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6

289.9K hrs min.      MIL-HDBK-217F (25

)

℃

40*125.2*113.5mm (W*H*D)

0.67Kg; 20pcs/14.4Kg/1.16CUFT

24V

48V

5A

2.5A

0 ~ 5A

0 ~ 2.5A

120W

120W

7.5A

3.75A

100mVp-p

120mVp-p

24 ~ 28V

48 ~ 55V

±1.0%

±1.0%

±0.5%

±0.5%

±1.0%

±1.0%

12V

10A

0 ~ 10A

120W

15A

180W (3 sec.)

100mVp-p

12 ~ 14V
±1.0%
±0.5%
±1.0%

■

 Features :

I/P-O/P:3KVAC     I/P-FG:2KVAC     O/P-FG:0.5KVAC     O/P-DC OK:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25

/ 70% RH

℃

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25  of ambient temperature.

℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
    EMC directives.
5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power.
    In case the adjacent device is a heat source, 15mm clearance is recommended.
6. 3 seconds max., please refer to peak loading curves. 
7. Derating may be needed under low input voltage. Please check the derating curve for more details.

120W Single Output Industrial DIN RAIL with PFC Function

‧

High efficiency 91% and low power dissipation

‧

150% peak load capability

‧

Built-in active PFC function, PF>0.93

‧

Protections: Short circuit / Overload / Over voltage / Over temperature

‧

Cooling by free air convection

‧

Can be installed on DIN rail TS-35/7.5 or 15

‧

UL 508 (industrial control equipment) approved

‧

EN61000-6-2(EN50082-2) industrial immunity level

‧

Built-in DC OK relay contact

‧

100% full load burn-in test

‧

3 years warranty