Moxa NPort 5430I 4 Ports NPORT 5430I User Manual
Product codes
NPORT 5430I
Industrial Networking Solutions
8-23
i n f o @ m o x a . c o m
w w w. m o x a . c o m
Serial Device Ser
vers
>
NPort® 5400 Series
8
NPort
®
5400 Series
4-port RS-232/422/485 serial device servers
Easy IP address confi guration with LCD panel
›
10/100M auto-sensing Ethernet
›
4 serial ports, with support for RS-232, RS-422, and RS-485
›
Built-in 15 KV ESD surge protection for all serial signals
›
Versatile socket operation modes, including TCP Server, TCP
›
Client, and UDP
Choice of confi guration methods: Web console, Telnet console,
Choice of confi guration methods: Web console, Telnet console,
›
and Windows utility
SNMP MIB-II for network management
SNMP MIB-II for network management
›
2 KV isolation protection for NPort® 5430I
›
NPort® 5400 device servers can conveniently and transparently
connect up to four serial devices to an Ethernet, allowing you to
network your existing serial devices with only basic configuration.
Data transmission between the serial and Ethernet interfaces is
connect up to four serial devices to an Ethernet, allowing you to
network your existing serial devices with only basic configuration.
Data transmission between the serial and Ethernet interfaces is
NPort® 5400 device servers can be used to connect different devices
for remote data polling, event handling, or data multicasting over
a TCP/IP network. Each serial port on the NPort® 5400 operates
for remote data polling, event handling, or data multicasting over
a TCP/IP network. Each serial port on the NPort® 5400 operates
NPort® 5400 device servers support redundant power sources and
provide both a DC terminal block input and a DC power jack input. The
two power inputs not only provide power redundancy, but also allow
greater flexibility for use with different applications.
provide both a DC terminal block input and a DC power jack input. The
two power inputs not only provide power redundancy, but also allow
greater flexibility for use with different applications.
An LCD panel is built into the NPort® 5400’s top panel, with four
buttons for inputting data, configuration, and selecting the operation
mode. The LCD panel displays the server name, serial number, and IP
address, and can be used to enter or modify parameters such as IP
address, netmask, and gateway.
buttons for inputting data, configuration, and selecting the operation
mode. The LCD panel displays the server name, serial number, and IP
address, and can be used to enter or modify parameters such as IP
address, netmask, and gateway.
bi-directional. By using NPort® device servers, you not only protect
your current hardware investment, but also allow for future network
expansion. You can both centralize the management of your serial
devices, and distribute management hosts over the network.
your current hardware investment, but also allow for future network
expansion. You can both centralize the management of your serial
devices, and distribute management hosts over the network.
independently to provide maximum versatility. For example, port 1 can
operate in Driver mode, port 2 in TCP Server mode, and ports 3 and 4
in TCP Client mode.
operate in Driver mode, port 2 in TCP Server mode, and ports 3 and 4
in TCP Client mode.
Network Readiness for up to Four Serial Devices
Independent Operation Mode for each Serial Port
User-friendly LCD Panel for Easy Installation
Redundant DC Power Inputs
Termination resistors may be needed in some critical environments
to prevent the reflection of serial signals. When using termination
resistors, it is important to set the pull high/low resistors correctly
to prevent the electrical signal from being corrupted. Since no set of
resistor values is universally compatible with all environments, the
NPort® 5400 has four sets of DIP switches on the bottom panel to set
the termination and pull high/low resistor values.
to prevent the reflection of serial signals. When using termination
resistors, it is important to set the pull high/low resistors correctly
to prevent the electrical signal from being corrupted. Since no set of
resistor values is universally compatible with all environments, the
NPort® 5400 has four sets of DIP switches on the bottom panel to set
the termination and pull high/low resistor values.
Adjustable Termination and pull High/Low Resistors
The certifi cation logos shown here apply to some or all of the products in this
section. Please see the Specifi cations section or Moxa’s website for details.